Repairs to uPVC Windows

uPVC windows are an excellent choice for modern homes. They are easy to maintain and durable, as well as long-lasting. They are not susceptible to decay or rust as aluminum and timber.

It is essential to clean and oil UPVC windows and doors regularly. This will save you from unnecessary repair costs and improve the efficiency of energy.

1. Broken Glass

The broken glass in your windows can cause serious damage to your home and even be fatal. It is essential to take the time to ensure that you are doing everything you can to keep your windows in good condition.

For single pane windows, it is fairly easy to replace them, and the new window will usually fit inside the frame that was previously installed easily. If windows with double panes are held together by internal beading, it is harder to remove and replace the old panes. In this instance, it is necessary to buy plastic spacers to aid in fitting the new pane into the window frame.

If you are going to try to remove the window panes yourself it is crucial to wear the appropriate safety equipment that includes gloves with a thick layer of material and protective eyewear. It is also an excellent idea to lay down a drop cloth before you start working on the glass to ensure that any shards fall onto the cloth instead of landing on the floor where they can be trampled on and cause further damage.

After the glass has been removed from the window, it's best to seal the gap with clear packaging tape or duct tape to block water and drafts from entering the property until a professional is able to come out and fix the window repair. It also acts as a barrier that will prevent any intruders from getting access to your home. If the gap between the window and the door is substantial, you may need to consider security screens that has windows. This will give you the best of both.

2. Sagging

Upvc windows and doors are a low-cost energy efficient, durable and long-lasting alternative to timber windows made of sash. However, over time they may be afflicted by a variety of issues, including sagging. A window that isn't properly aligned can cause problems with light, draughts and even security. If you find that your uPVC window is beginning to lose its shape, it's important to act quickly to prevent the problem from worsening.

Repositioning the hinges can aid in fixing a window which is sliding. First, you'll need to unblock the windows so you can get at the frame. After that, using a screwdriver, you can remove the top and bottom hinges and adjust them by turning them clockwise or anti-clockwise. Once you've repositioned the hinges, close your window and verify the fit. If you are happy with the fit of your window, tighten the screws to keep them in place.

If you are unable to reposition the hinges you may need to replace the seal. Over time, rubber seals lose their elasticity and become dry, which causes them to lose tightness. If this happens, it's crucial to replace the seal as soon as possible so that your uPVC windows are watertight and secure from draughts.

uPVC handles may also become loose. Most often it is due to screws that have become loose over time. However, it can be due to the fact that the handle mechanism has been worn out. Luckily, it's not difficult to repair a loose uPVC window handle yourself. First, you'll need close your window and do an experiment to ensure that it fits. The corners of the sash should be aligned with the casing joint. If it isn't, you can use a screwdriver to loosen the handle and return the mechanism to its original position.

3. Water Leaks

If you're waking up to wet floors and damp walls each time it rains it's crucial to take action. Leaks of water from windows can cause structural damage to your home, and affect your ability to regulate the temperature in your home. Most often, uPVC window leaks are caused by damaged or missing sealant.

This is a fairly simple fix that can be done by any competent DIYer. Depending on the severity of the problem the old caulking might need to be removed before a new layer is applied. It is essential to keep in mind that when it is about uPVC window repairs you should not be tempted to apply too much caulk' as this will only make the area more difficult to clean and could reduce your energy efficiency.

It is important to check that the drainage holes are free of debris and that the sill pan is placed correctly so that it drains away from the window. In more severe instances, you may need to replace the window.

Mold spots and rotted sills are other signs of water leakage. This fungus thrives under conditions of dampness and can spread quickly throughout the house.

If the leakage occurs between the double-glazed glass it is more likely the issue is more with the seal rather than the frame. It is also possible to be fixed by an Upvc Window Repair window expert who can replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or uPVC window repair loose and open with a breeze It could be the hinges that are at fault. Any competent DIYer can replace the hinges in a matter of minutes.

Like any mechanical component, hinges can wear out over time. It is very easy to change the hinges on a window however it is simpler if you have someone to help you hold the frame.

It is also important to verify that the uPVC hinges are opening and closed in the right direction. Look for the arrows that are on each hinge to determine which direction the window should be opened.

The issue can be caused either by opening the window incorrectly or by a poor installation at the factory. Sending us a picture via our website will often solve the issue. We are happy to offer suggestions.

Regular lubrication of the hinges is essential. Applying a light engineering lubricant to the hinges is a great way to do this. We recommend using the lubricant that doesn't contain solvents, such as 3-in-1 Multi-Purpose oil. Regularly lubrication makes the window easier to open and close. It can also prevent corrosion and reduce the possibility of sticking. This should be done at least every year. WD40 and other solvent-based lubricants are not recommended as they could damage parts of your uPVC window.

5. Draughts

Draughts in Upvc windows can be caused by a variety of various factors. The hinges, also due to wear and tear can become misaligned, this can cause an opening to appear where the sash joins the frame. If they're beyond repair, uPVC window repair it could be necessary to get them re-aligned. Secondly the interlock, this is located on the hinge of the window and can also become misaligned, again it may be possible to just give them a clean but in some instances it could be necessary to get them replaced.

The second most frequent cause of draughts is the window seals. These can become worn down or damaged over time, and let air escape through these gaps. Replacing these with high-quality weatherstripping is a good way to stop draughts. Replace the upvc windows with low-emissivity glasses. This will help control indoor temperatures and lessen the risk of draughts.

Lastly, one of the most effective ways to cut down on the draughts in your home is to use an draught excluder. These are typically made of fabric filled with some kind of filler. They can be placed on the top of your windowsill. These will help to block out cold air and keep your home warm and cosy!

Your windows made of upvc will remain a great source of insulation and security to your home by performing regular maintenance and repairs. It is crucial to keep in mind that all windows will eventually get worn out and it may be more cost-effective to replace them rather than repair them. If you have any problems with your Upvc window, it's best to consult a professional immediately.