Double Glazing Door Lock Repairs

Has your uPVC window or door mechanism started to fail? Perhaps the window or door handles don't meet up correctly or are difficult to use.

It is essential that your double glazed doors function smoothly, or else you will lose energy and increase the chance of burglary. Owen the Locksmith can repair your door lock for an affordable cost.

Snapped Key

It can be a hassle when a key snaps into the lock. It could also be a security problem, as it may make you vulnerable to a burglar if the door is not locked. Fortunately, Repairmywindowsanddoors there are some simple fixes you can try to resolve the issue and get your door operating properly again.

Keep calm. If you panic and start doing a lot of fumbling around you may end up pushing the damaged piece of the key further into the lock, thereby making the situation even more difficult.

Spray WD-40, or any other penetrating oil, into the lock. This will help the broken piece come out more easily. You can also use a screwdriver to help break up any stuck pieces that might be blocking the way. If you happen to have a bit of the key that is visible, you can use a paperclip or some other metal object with a thin surface to grab it and then pull it out. Both methods work, but be careful not to push the damaged key further into the keyway.

Some paperclips have grooved edges that could serve as hook extractors and some Jigsaw blades can also be used for this purpose. If you don't have any of these available, you can use needle-nose pliers that bend to create hooks. Additionally, you can use a pair tweezers to grasp and pull out the last bit of the broken keys.

If you are unable to remove the broken key piece Use a lock deicer. It is available in most hardware stores and is used to freeze any moisture present inside the lock.

If none of these methods seem to be helping you, it's time to call in a locksmith. The experts at Fitlocks can quickly resolve issues with uPVC door mechanisms and locks such as snapped keys and broken handles. They can also modify your double glazing door mechanisms to make them easier to operate. Book a double glazing repairs near me glazing repair via our website, or give us a call to discuss your requirements.

Broken Cylinder

A broken cylinder can pose a serious security risk. A locksmith professional can fix the cylinder. A locksmith must tap the cylinder in order to repair it. They can do this using the hammer or any other tool, but the most efficient method is to employ an extended match or piece of wire. Then, put the match's tip or wire in the keyway. The locksmith can strike the lock to crack it open. This is more secure than using a hammer that could cause damage to the lock.

The most frequent cause of cracks in the cylinder head is overheating. This can happen when the cylinder block and head are made of different metals, such as cast iron and aluminum. When various metals heat up and cool down at different rates, it can cause localised hotspots that expand faster than the rest of the cylinder head, leading to cracks.

Another possible cause of cracks in the cylinder is corrosion. If the head and block of the cylinder are not maintained correctly they may rust or corrode and cause them to expand more than expected. This can cause cracks in the future.

If your uPVC door or window lock is stiff or requires lots of pressure to turn, it could be due to a number of things. This problem can be caused by a malfunctioning locking mechanism or misalignment, and also a worn out handle.

Fortunately, this is an easy and affordable fix for repairmywindowsanddoors the majority of homeowners with double glazing. A professional locksmith will usually solve this issue within an hour of arriving at your property. They can repair the locking mechanisms, or change the window handles and replace the gearboxes, depending on your particular requirements. A locksmith with experience can always advise you on the most cost-effective solution for your home. They can even recommend upgrades to high-security 3 Star TS007 euro cylinders that will give you an additional layer of protection against burglars. It's a small amount to get the peace of mind that comes from knowing that your uPVC door is secured.

Broken Handle

Window handle locks are complex mechanisms that become less effective with age and use, so it's no surprise that they can break. It isn't easy to determine the cause of a broken window handle lock and then fix it properly.

Repairing your damaged handle, whether it's an internal latch or the locking mechanism can increase the security of your uPVC door and stop draughts. It could be costly to replace or repair the handle in a way that isn't done correctly. It can also damage the frame and lock of your door.

With the window in the open position, loosen the screw that secures the handle by using a screwdriver. The screw should be located on the inside of the backplate. It is typically hidden by the cap of the screw to enhance the appearance. You should not be able to replace any internal parts of the handle such as the levers and plates on either side. It is best to keep them in the same place so you can re-install them in the event of a need.

Then, rotate the handle until it's 90 degrees to the window frame. Finally, loosen the screw at the back of the handle that fixes it to the internal spindle by using a second screwdriver. Once the screw is loose, pull the handle out and remove the broken spindle. Replace it with a new spindle, ensuring it's the same length (you can purchase them online or at hardware stores). Securely screw it into the frame. Don't over tighten the screw because this could harm the handle as well as the window frame.

Close the handle and try it. Hopefully, it will work smoothly and you'll be able unlock your window.

Be sure to double-check that your upvc door repairs near me window is shut correctly while you're working with the handle. If they're not closing properly, you could experience damp and draughts inside your home as in addition to compromising the efficiency of your home's energy usage. A local window company, like Core Sash Windows, will be in a position to adjust the hinges on your window frames to ensure they can shut properly.

Broken Spindle

It is often the case that the spindle inside the handle is broken, not the handle itself. This is especially common with uPVC tilt-and-turn windows. These windows require a handle that operates a locking device in the frame of the window. The handle is connected to a central rod that activates a series of mushroom-shaped locking cams that lock into the window frame keep. If the dead latch mechanism does not open when the handle is turned, it is likely that the spindle has broken This can be a frustrating problem.

There are solutions to this problem. A professional locksmith can quickly and efficiently repair this problem. They can disassemble the window handle by using a tool that removes the wheel part of the mechanism where the spindle is. This can be done without damaging the handle or causing other damage to the window frame.

Once the wheel is removed, the technician will inspect the spindle and determine what has caused it to break. This involves disassembling the spindle and inspecting every component, observing any wear or RepairMyWindowsAndDoors damage. This process is usually carried out by technicians in a clean and safe environment.

Then, clean the damaged spindle. This will remove any dirt or debris which may be obstructing it from operating normally. The spindle may then be repaired or replaced. If it is being replaced the technician could use an identical dowel size to the one used in the first and drill mating holes into both pieces of the spindle. This ensures that the new spindle is a precise fit with the handle.

If the spindle is damaged and cannot be repaired, it could need to be replaced entirely. Home centres sell generic replacements but If the style of your window is unique then it will be necessary to contact a wood worker or cabinet maker who can make the exact part for you. Once the spindle has been installed, it can be connected to the handle. Line up the screw holes on the handle to the existing screws in the frame. Once the handle is firmly set, you are able to operate your uPVC windows.