Reasons Why Your Nissan Qashqai Key Fob Won't Work

The Qashqai has a distinct SUV-like appearance due to its larger dimensions. Moreover, the 19-inch wheels on Ti and ST-L models may be a bit spongy at times. The front tyres of Qashqai may also lose grip on rough surfaces and its CVT can sometimes display a wrist-flexing torque steering.

This is usually caused by dead batteries that can be replaced in a matter of minutes. Make sure the new battery is of the same size, voltage and specifications.

Water Damage

One of the most common reasons why a Nissan key fob will give the "key ID is incorrect" message is due to water damage. The rubber seals on the key fob guard the chip's electronic components, however long-term exposure to moisture can cause it not to work correctly. It is common to observe this if your key fob was dropped into the ocean or in a pool. However, it can occur when it becomes wet from showers or soapy hands.

If your key fob was exposed to water over an extended period of time then you might need to clean it with isopropyl or electronic cleaner. It may also need to be taken to a specialist for repair or replacement.

If your key fob need to be replaced the process is simple. Make sure you have the proper multipack (CR2032, 3V). Remove the front and back cases using a flathead screwdriver. Remove the metal clips, remove the old battery and replace it. After reassembling the fob, put the mechanical key back into place and verify that it operates correctly. If it does not it, you'll need to bring it to an Nissan dealer or a professional auto locksmith to replace the key chip. Fortunately the chip isn't often damaged by water exposure, so this should not be too expensive.

Dead Coin Battery

Another common reason your Nissan Qashqai key fob may not function is because the battery for the coin is dead. These batteries usually last 3-5 years but can go bad over time, particularly if the fob is dropped frequently. You could try replacing the battery with a fresh one, but make sure that it's the same size and voltage as the original. If you install a new battery, it could cause the key to be assigned a wrong key ID. This could prevent it from being connected to your vehicle.

The most effective method to replace the battery in a Nissan Qashqai key fob is by removing the fob with a small flat head screwdriver. The screwdriver should be put into a small notch on the bottom of the key fob. The screwdriver should be gently twisted to separate the two halves. Then, remove the old CR2025 button cell battery and replace it with a new one after noting its position in the fob.

Check the terminals for any water damage or dirt before installing the new battery. If there is, nissan qashqai key fob clean the terminals with a small amount of isopropyl alcohol. You'll also need to make sure the pole cables are plugged in properly - they must be connected to the positive and negative poles of your battery, respectively.

Fault Diagnosis

If your Nissan Qashqai key fob stops working after exposure to pure rain or tap water, it may be a sign of a chip issue inside. Changing the battery won't fix this, and you'll have to purchase a new key fob. If you dropped the key fob on the ground and it stopped functioning immediately it is likely because it has damaged the internal chip. It is usually possible to get the key fob back to work once again if it is removed and clean the chip using paper towel and isopropyl alcohol and then put it back in.

One common error you may notice on your dashboard is "Key ID Not Correct." The car is unable to recognize the key fob, and Nissan qashqai key fob therefore will not allow the vehicle to start. The problem can be caused by a variety of factors including water damage, undetectable issues in the circuitry of the key fob, or RFID interference.

The key fob will cease to function in the event that the 12 volt batteries are dead or do not provide enough electric current. This will affect the nissan juke key fob Qashqai's keyless system central locking, as well as the capability to start the engine using the key fob. If you're unable to unlock or lock the door by hand You should examine the batteries in your key fob and make sure they're in good shape. You can also try reinstalling the battery to reset your transmitter.

Reprogramming

If the key fob was not submerged into saltwater it should return to life with a simple wash of clean water. You can also clean the electronic chip by using isopropyl or electronic cleaner. If none of these work, you may need to replace the key fob.

If your Nissan Intelligent Key is still not functioning, there may be an issue with the connection between it and the car. To relink it, start by turning the key into the ignition but without starting the car. Continue to do this until the hazard light blinks twice. After that, turn the car off and take out the keys.

Then, you need to then open the fob compartment in your vehicle. It's usually found on the door jamb or the handle for the driver's door. Find the button that says "program" and press it. You will hear a sound after the process is completed.

Now that your Intelligent Key is relinked to the car is the time to test it out. Take a step away from the vehicle, and click all of the buttons on it. If the lights flash and the horn squeaks it means the key has successfully connected to the Nissan. You can also test it near the Nissan.