Reasons Your fiat key 500 Key Fob Won't Work

A fiat keys replacement 500 key replacement cost (click through the next internet site) 500 key fob is a convenient way to unlock the doors and start the car. However, there are a variety of reasons why the fob won't be working. This includes a dead battery or water damage, problems with receiver modules, as well as interference.

This listing is for a NEW replacement Fiat Flip Key Remote that is similar to the Ilco brand. It must be professionally programmed (click here to find local automotive locksmiths). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

The most common reason your 500 key fob doesn't function is a dead battery. Modern key fobs have limited operating range and must be within just a few inches of the vehicle to function. If you are far from your car and push the keyfob button it won't respond and display the message "Key Fob Not Detected".

If this occurs, replace the coin-cell battery (Part Number CR2032) by a fresh one of a reliable brand, such as Panasonic Duracell or Energizer. They are usually available in your local hardware store or on the internet.

You can test the battery on your coin-cell by pressing the buttons while you are standing close to your Fiat 500. The parking lights will flash and the key fob will operate the lock and unlock switches.

If the key fob won't work after replacing the battery, it might be damaged by water, which prevents it from communicating with the receiver module inside your vehicle. Water damage can happen in a number of ways, from small splashes to submerging the fob in salt water at the beach. If you suspect that your fob was exposed to water, you can place it in a rice bag to draw out the moisture. If that doesn't work, your fob will probably need to be reset by an experienced locksmith or dealer.

Water Damage

Water damage can happen if you immerse the fob in the ocean or wash it in a washing machine. Saltwater is particularly dangerous to the fob's circuit board that can cause it to short out and eventually die. In the event that you let your fob get wet, it's not a good idea, but if you drop it in the water in a cup or don't remember to take it out of your pocket before you run the washer Don't give up hope.

Remove the battery first. Clean the electronic chip with isopropyl alcohol or a similar product and then dry it thoroughly before replacing the battery. Next check the fob to see if it works. If the key still doesn't work, it may need to be programmed again. This is usually done by a professional or dealer auto locksmith.

If the key is more recent and has not been programmed to your car It will most likely need to be replaced completely. This is an easy process that can be carried out by a professional automotive locksmith. The locksmith needs to cut the key to match the ignition of your car. The locksmith will also have to reprogram your fob into the car's system. This is a simple and affordable process which can be completed within the same day.

Receiver Module Issues

The 500 key fob could be inoperable because it's out of range. The remote has a maximum range of 30 feet. Therefore, should you be too far away from your vehicle, it won't respond to your commands. It is possible to fix this by moving the remote closer to your vehicle until it responds.

If your fob doesn't work after you replace the battery in the coin, also called a "button", "watch" or "button" It could be due to a problem with the internal circuit board. Reprogramming the fob typically resolves this problem. There are instructions on how to do this for most vehicles by searching YouTube or consulting the owner's manual.

It may be necessary to replace the clips made of metal that hold the coin batteries in their place. If they lose tension it could hinder the battery from sitting properly and can cause the remote to malfunction.

In rare cases the fob may be out of connection with your vehicle as a result of hardware or software issues. This issue can be fixed by visiting your local dealer or auto-locksmith to reprogram your key fob. In some cases it may be necessary to reinstall the software in your body control module as well.

Interference

In addition to a dead coin battery The key fob may not be receiving or transmitting a signal due to interference. This can happen when the key fob is in proximity to an electronic radio transmitter (cell phones and radar detectors) or another source of electromagnetic radiation. The key fob might not work because of a weak connection to the buttons or water damage, or damage to the internal chips.

If your key fob suddenly stopped working, or you have tried everything at home to fix it (e.g. replacing batteries, reprogramming or using the spare key fob, it could have a defective receiver module on your 500. The receiver module, located under the dashboard, detects radio frequency signals from your key fob. It converts the signals into electronic commands which are then read by the vehicle.

There is a straightforward method to reset the 500's in-board system including the keyfob. Disconnect the battery for 15 minutes by removing first the negative cable, then the positive cable. Then, reconnect the battery. This will get rid of any remaining electricity and restart the car's computers, which can help get your key fob working again. If the issue continues you should seek out a certified technician. They will be able to determine the exact cause of issues.