Reasons Your Fiat 500 Key Fob Won't Work

A fiat keys (mouse click the following web page) 500 key fob allows you to easily open doors and start your vehicle. There are a variety of reasons why the fob could stop working. This could be due to a dead battery water damage, issues with the receiver module, and interference.

This listing is for an NEW replacement fiat 500 key Fiat Flip Key Remote that appears similar to the Ilco brand. It needs to be professionally programmed (click here to find local locksmiths for automotive locksmiths). It comes with trunk, lock and unlock buttons.

Dead Coin Battery

A dead battery is the most common cause of your 500 key fob not working. Modern key fobs only have only a limited range of operation and must be within a few inches of your vehicle in order to work. If you're far away from your vehicle when you press the key fob button the car won't respond and will display the "Key Fob Not Detected" message in the instrument cluster.

If this happens, replace the battery in the coin cell (Part number CR2032) by a new one from a reputable brand such as Panasonic, Duracell, or Energizer. They can be found in your local hardware store or on the internet.

You can test the battery in the coin-cell by pressing the buttons while standing near your Fiat 500. The parking lights should blink and the key fob should operate the lock and unlock switches.

If the key fob doesn't function after replacing the battery, it might be damaged by water that blocks it from connecting to the receiver module inside your car. Water damage can happen in a variety of ways, from an accidental splash to submerging the fob in salt water at the beach. If you suspect that your fob was exposed to water, you can try placing it in a dry rice bag to draw the moisture out. If this doesn't work, your fob may need to be reprogrammed by an experienced auto locksmith or the dealer.

Water Damage

Water damage can happen if you submerge the fob in the ocean or wash it in a washing machine. Saltwater can cause the circuit board to short and eventually die. Getting the fob wet is not an option however, if you drop it in a cup of water or fail to remove it from your pocket before you run the washer Don't give up hope.

First, remove the battery from the fob. Clean the electronic chip with isopropyl alcohol or a similar product and dry it thoroughly before replacing the battery. Check the fob to check if it's functioning. If the key still doesn't work, it may have to be changed. This is typically handled by a dealer or professional auto locksmith.

If the key is older and has never been programmed to your car It is likely that it needs to be replaced completely. This is a simple process that can be handled by a professional locksmith for automotive use. The locksmith will need the key cut to match the car's ignition. The locksmith will also have to program your fob into the car's system. This is an affordable and quick procedure that can be completed in the same day.

Receiver Module Issues

Your 500 key fob might be inoperable because it's out of range. The remote usually has an area of 30 feet or less, and if it's too far away from your car it won't respond to your commands. This can be easily fixed by moving it closer to your vehicle until it starts responding.

If your fob doesn't work after replacing the battery in the coin, also called a "button", "watch" or "button" it could be due to a problem with the internal circuit board. In most cases, reprogramming the fob can resolve the problem. The instructions are available for the majority of vehicles on YouTube or in the owner's manual.

You may need to replace the metal retaining clips that hold the coin battery. If they lose tension, it could prevent your coin battery from being properly seated, causing your remote to malfunction.

In rare cases it is possible that the fob will become desync'd with your vehicle because of software or hardware issues. This can be a major problem, but you can frequently fix this issue by visiting an auto locksmith to reprogram your fob. In some instances the software may require reinstallation into your body control modules.

Interference

In addition to a dead battery on a coin The key fob may not be able to receive or transmit signals due to interference. This could occur if the key fob is located near an electronic radio transmitter (cell phones and radar detectors) or another source of electromagnetic radiation. Other reasons why the key fob might not work could be due to a weak connection to the buttons, damage to the internal chip, or water damage.

If the key fob has stopped working one day suddenly, or after trying every option at home to fix it e.g. You may have a faulty 500 receiver module after you've tried replacing the battery, reprogramming it, or using an alternative key fob. The receiver module, which is located under the dashboard, receives radio frequency signals from your key fob. It converts them into electronic commands that the vehicle interprets.

Fortunately, there's an easy method of resetting all on-board systems in your 500 device, including the key fob. Disconnect the battery for 15 minutes by removing first the negative cable, then the positive cable. Then reconnect the battery. This will clear any residual electricity, and restart the computer of your car. This will help you get your key fob working again. If the problem persists you should seek out an expert technician. They will be able to identify the root of any problems.