Fiat 500 Replacement Key Fob

If your 500 remote key fob isn't working, it may be time to replace the battery. However, if you replace the battery and it continues to stop working the issue could be elsewhere.

At United Locksmith, we specialize in the creation of new keys for classic cars. We have the tools and visit the next internet site components required for this service.

Dead Coin Battery

The most frequent reason why your Fiat 500 key fob will not unlock or lock the doors is a dead battery. The battery inside the key fob will drain quickly when you don't use it often enough. If your remote began to show signs of weakening like a loss of range, and then stopped working completely the battery could be dead.

The battery in the key fob is held in place by steel clips that retain it. If the clips aren't secure, it can cause contact issues that will stop the remote from receiving power. With a small flathead screwdriver, push the clip that holds the retaining pin open to remove the battery, and replace it with a brand new one. Make sure that the battery you choose to use has the same voltage, size and specification as the original.

The exposure to water can cause the key fob to corrode or become damaged. Even a quick bath in soapy, warm water could damage the chip. It is recommended to keep your key fob in a dry area.

Water Damage

Water damage may be the cause of your key fob's inability to function properly. Key fobs have rubber seals to protect them from being damaged by light rain or a splash of water, however it is crucial to keep your car keys out of the pool, ocean, and washing machine!

The key fob contains an electronic chip in it that transmits a signal car's immobilizer system. This is the reason why your 500 can lock or start, but should the chip become saturated, it won't be able to longer function.

You can try cleaning the inside electronics of your keyfob using isopropyl alcohol, or an electronic cleaner to see if they are still good. However, it's better to purchase a new one from a dealership instead of trying to repair a key fob that has been submerged in salt water.

While a replacement fob might cost you a bit of money, it is much cheaper than having to pay for your Fiat 500 to be towed to the dealership and repaired! In addition, you can do it yourself in a few easy steps. Be sure to use the correct battery type before you attempt to open your key fob. You can find step-by-step instructions for Continue any car keyfob online.

Faulty Chip

The chip inside the key fob communicates with the immobiliser on your car to ensure that your vehicle will start only when the right keys are in place. If the chip is damaged or destroyed the car will not start, no matter what you do.

Water damage or a dead phone battery are among the most frequent causes of the chip being damaged. Whatever the reason, it is an ideal idea to hand this work to a locksmith, as they will be able to repair the chip for you swiftly and at a reasonable cost.

If your key fob stops working after exposure to clean water from the tap or rain, take off the battery and clean the electronic component with a towel to ensure it's dry before putting it back into. If the key fob fails to work it's most likely a fried chip and must be replaced.

Some people go to their dealer if they require an entirely new Fiat fob. But, this can be a costly option. If you're looking for a low-cost solution to have your Fiat key fob repaired Look no further than United Locksmith. We have the tools and knowledge necessary to repair your fiat key fob programming key fob in a quick and professional way.

Faulty Receiver Module

Fiat key fobs send an electrical signal to the vehicle that can unlock and close doors (and start the car for those with an automatic transmission) up to 50 feet. There are a variety of reasons why a fob could stop working. This includes a dead coin-battery or water damage, worn-out buttons or a receiver issue signal interference, or malfunctioning chips.

If the fob was placed in a pocket which has suffered severe trauma (such as being dropped on the floor, or washed in a washing machine) it might not be in a position to connect with the Body Control Module (BCM) of the vehicle. The BCM is a security device that only accepts signals from genuine keys.

You will need to replace the fob if this happens. A professional locksmith will manage the entire process of replacing keys including programming a brand new key for your 500. In fact, they can even provide you with a clone key that functions exactly the same as the original fob (and costs less than the cost).