Repairs to uPVC Windows

uPVC windows are a fantastic choice for modern homes. They are easy to maintain and durable, as well as long-lasting. They are not susceptible to rot or rust like aluminum or timber.

Regularly cleaning and lubricating UPVC windows and doors is vital. This will reduce costly repairs and improve energy efficiency.

1. Broken Glass

If the glass in your window is broken it could cause a large amount of damage to your home, making it very dangerous and potentially fatal. It is crucial to take the time to make sure that you're doing all you can to keep your windows in good condition.

Single-pane windows are relatively easy to replace and will usually fit into the old frames very easily. If you have double-paned windows which are held together by internal beading, it will be difficult to remove and replace the old panes. In this situation you'll need to find some plastic spacers that will help the new pane to fit perfectly into the frame of the window.

Wearing eye protection and thick gloves is a must when you are planning to remove the glass by yourself. You should also lay down a dropcloth before you begin working on the window panes to ensure that any shards of glass fall onto the fabric and not on the floor which could cause them to be trampled.

Once the glass is removed from the window, it's best to cover the gap with clear packaging tape or duct tape to block drafts and water from entering the home until a professional is able to come out and repair the window. This also serves as an obstruction to prevent criminals from getting into your home. If the gap is particularly large, you might be interested in an alarm door that comes with an integrated window, since this will offer the best of both worlds.

2. Sagging

Upvc is a long-lasting and energy efficient alternative to timber sash windows. However, over time they are susceptible to a range of problems including sliding. A sagging uPVC window could cause issues with light, draughts, and even security. It's crucial to act as soon as you notice your uPVC windows are sagging.

Repositioning the hinges could aid in fixing a window which is sagging. To do this, you'll need to open the window to get to the frame. Then, using an screwdriver, unscrew the hinges at the top and bottom and adjust them by turning them clockwise or counter-clockwise. Once you've repositioned the hinges, close your window and verify the fitting. If you are happy with the fit of the window, tighten the screws to keep them in the right position.

If you cannot reposition the hinges, you may have to replace the seal. Over time, rubber seals lose their elasticity and dry out, which causes them to lose tightness. If this happens, it's important to replace the seal as fast as possible to ensure your uPVC windows remain watertight and secure from draughts.

UPVC handles can also become loose. This is usually due to screws that have loosened over time, but it can also be due to the handle mechanism wearing out. Fortunately, it's easy to fix a loose uPVC window handle yourself. First, you'll need to shut the window and then perform a test fitting. The joint at the corner of the sash should be aligned with the joint on the casing. If it doesn't then you can use a screwdriver or a wrench to loosen the handle, and then return the mechanism to its original its original position.

3. Water Leaks

If you awake to damp floors and mouldy walls each time it rains, it's important to take action. Water leaks from windows not only lead to the destruction of your home's structure but also hinder your efforts to control the temperature in your home. The most common cause for leaks in uPVC windows is that the sealant surrounding the frame is damaged or missing.

This is a simple fix that can be done by any DIYer who is competent. Depending on the severity of the problem is, the old caulking may have to be removed. It is essential to keep in mind that when it comes to upvc window repairs (www.koreathai.com), do not be tempted to 'over-caulk and then make the area more difficult to clean and could decrease the efficiency of your energy usage.

It is important to check that the drainage holes are free of debris and that the sill pan is angled properly so that it drains away from the window. In more severe cases, you may need to replace the window.

Mold spots and rotten sills are other signs of water leakage. This fungus thrives in damp conditions and can quickly spread throughout the house.

It is also important to remember that if the leakage is coming from between the glass of your double-glazed windows it may be more likely to be an issue with the glass seal, rather than the frame or sliding. A uPVC specialist can fix this issue by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or are loose and open with ease It could be hinges that are at fault. They can be replaced by any competent DIYer and are usually completed in a matter of minutes.

Like all mechanical parts hinges will wear out over time. It's easy to change the hinges on a window, but it's easier if someone else helps you hold the frame.

It is also important to verify that the uPVC hinges are opened and closed in the right direction. You can do this by checking for the arrows on each hinge. This indicates the direction in which the window should open.

The issue can be caused by opening the window incorrectly or a faulty installation in the factory. Sending us a photo through our website can often resolve the problem. We are more than happy to provide assistance.

Regularly lubricating the hinges is also necessary. This can be done by applying a light engineering oil on the hinges. We suggest using a solvent-free lubricant, such as the 3-in-one Multi-Purpose oil. Regular lubrication can help the window operate and close more smoothly. It can also stop corrosion and reduce the risk of sticking. It is recommended to perform this every year. WD40 or other solvent-based oils should not be used as they could damage your uPVC windows.

5. Draughts

Draughts can be caused by a variety of different things. Firstly the hinges, again due to wear and tear could become misaligned. This can cause an opening to appear between the sash and Upvc Window Repairs the frame. If they are damaged beyond repair, it might be necessary to have them realigned. The interlock, which is located on the hinge side of the window, can also become misaligned, again it's possible to give them a clean but in some instances it could be necessary to have them replaced.

These seals can wear down or be damaged over time, allowing air escape. Replacing these with high-quality weatherstripping can help keep draughts at bay. Another alternative is to replace the upvc window with glass that is low-emissivity, this will help to regulate indoor temperatures and will reduce the risk of draughts.

Another method of reducing draughts effectively is by using a Draught-excluder. These are typically fabric tubes filled with a filler that can be put on top of your window sill. They will keep your home warm by blocking out cold air.

With a little maintenance and repair your windows made of upvc will continue to provide a great level of security and insulation for your home. It is crucial to realize that all windows have a life span and there may come the point when it's more efficient to replace them than repair them. If you have any problems with your upvc window, it's best to consult an expert as soon as you can.