Repairs to uPVC Windows

uPVC windows are an excellent choice for modern homes. They are durable, long-lasting and easy to maintain. As opposed to aluminium and timber they do not corrosion or rot.

It is important to clean and oil UPVC windows and doors on a regular basis. This will reduce repair costs and increase energy efficiency.

1. Broken Glass

If the glass in your window is broken it can cause a great amount of damage to your home, making it very dangerous and potentially fatal. It is essential to take the time to ensure that you are doing everything you can to ensure that your windows are in good repair.

Single-pane windows are fairly simple to replace, and they will usually fit into the frames of the past easily. If you have double glazing repair-paned windows that are joined by internal beading, it will be difficult to remove and replace the panes that were previously in use. In this situation, you will need to source some plastic spacers that assist the new pane to fit perfectly into the frame of the window.

If you're planning to attempt to remove the window panes yourself it is important to wear the proper safety gear, including thick gloves and eye protection. It is also recommended to lay down a dropcloth before you begin working on the window panes to ensure that any shards fall on the fabric, not onto the floor and could be trampled.

Once the glass has been removed from the window, it's best to cover the gap with packaging tape or duct tape to block water and drafts from entering the home until a professional is able to come out and repair the window. This also serves as a barrier to prevent any intruders from making their way into your home. If the gap is large, you may think about the security door with an integrated window as it will provide the best of both worlds.

2. Sagging

Upvc is a long-lasting energy-efficient, cost-effective and economical alternative to timber sash window. As time passes, they may be affected by a variety of issues that include sagging. A sagging window in uPVC can cause problems with light, draughts, and even security. It's crucial to act when you notice your uPVC windows are falling down.

To fix a sagging window you can try to reposition the hinges. To do this, you'll have to open the window so that you can get to the frame. You can then unscrew both the hinges at the top and bottom using a screwdriver, and then adjust the hinges clockwise or counter-clockwise. Close your window to check the fit after you've relocated your hinges. If you are happy with the fit of the window, you can tighten screws to hold them in the right position.

If you aren't able to move the hinges you may require replacing the seal. Over time, rubber seals lose their elasticity and become dry and cause them to lose tightness. It is crucial to replace your seal as quickly as you can to keep your uPVC window watertight and draughtproof.

uPVC handles can also become loose. Most often it is due to screws that have come loose over time. However, it could be due to the fact that the handle mechanism has been worn out. It's a good thing that it's simple to fix the handle of a window that is loose yourself. First, you'll need to close the window and perform an initial test fit. The joint at the corner of the sash should be aligned with the joint on the casing. If it does not, you can use the screwdriver to loosen the handle. Then, turn the mechanism back into place.

3. Water Leaks

If you wake up to wet floors and damp walls every time it rains it's crucial to take action. Windows that leak water do can not only cause destruction of your home's structure but also hinder your efforts to regulate the temperature within your home. The most common reason for leaks in uPVC windows is that the sealant surrounding the frame has been damaged or not present.

This is an easy fix that can be completed by any DIYer who is competent. Depending on the severity of the problem is, the old caulking may have to be removed. When it is time to uPVC repair, it is important to avoid 'over-caulking'. This will only make your window harder to clean and reduce its energy efficiency.

It is essential to ensure that any drainage holes are clear of debris and that the sill pan is placed correctly so that it drains away from the window. In more serious situations, you might have to consider replacing the window.

Other indicators of water leakage are decayed sills and the appearance of black spots of mold on the wall near the window. The is a fungus that thrives in damp conditions and can quickly spread throughout the home.

It is also important to note that if the leak is coming from between the glass in your double glazed windows, it is more likely to be an issue with the glass seal rather than the frame or sliding. It is also possible to be fixed by an uPVC window specialist who will replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or slack and blow open with a breeze It could be hinges at fault. These are easily repaired by any DIYer who is skilled and can be done within a few minutes.

Like any mechanical part hinges will be damaged over time. The process of replacing a hinge on a window is essentially a very simple procedure, but it is easier with someone else to assist in holding the frame in place.

Verify that the uPVC hinges open and close in the proper direction. Look for the arrows that are on each hinge to determine which way the window should be opened.

The issue can be caused either by opening the window incorrectly or a faulty installation in the factory. It is usually possible to fix the issue by sending us a picture via our website and we will be happy to give you suggestions.

Regular lubrication of the hinges is also necessary. This can be done by applying a light engineering oil on the hinges. We suggest using a solvent-free lubricant, such as the 3-in-one Multi-Purpose oil. Regularly lubrication will help the window operate and close more easily. It can also lower the possibility of a window sticking and prevent corrosion. This is recommended to be done at least every year. WD40 and other solvent-based fluids are not recommended since they will damage parts of your uPVC window.

5. Draughts

Draughts in Upvc windows can be caused by a few various factors. Firstly the hinges, again due to wear and tear could become misaligned. This can cause a gap to form where the sash joins the frame. These can be easily repaired by giving them good clean, but when they're beyond repair, it might be necessary to get them re-aligned or replaced. Second, the interlock can be misaligned. It is located on the hinge's side and could require to be cleaned. In some instances it is possible to replace these.

The next common cause of draughts is the window seals. They can become worn down or damaged over time, and allow air to escape through these gaps. Installing high-quality weatherstripping can help keep draughts at bay. Another alternative is to replace the upvc window with low-emissivity glass. this will help to regulate indoor temperatures and again will lessen the possibility of draughts.

Another method of reducing drafts effectively is to use a Draught-exclusion device. These are typically fabric tubes filled with a filler that can be put on top of your window sill. They can help keep cold air out and keep your home warm and cozy!

The windows made of upvc can remain a great source of insulation and security for your home with regular maintenance and repairs. It is crucial to keep in mind that all windows will eventually wear out and it is cheaper to replace them rather than repair them. If you have any problems with your Upvc window it is recommended to speak with an expert immediately.