Fiat 500 Replacement Key Fob

It may be time to replace the battery if your 500 remote key for fiat 500 fob isn't working. However, if you replace the battery and it continues to stop working it may be elsewhere.

United Locksmith specializes in the creation of new keys for classic vehicles. We have the tools and parts needed for this job.

Dead Coin Battery

The most common reason why your Fiat 500 key fob will not unlock or lock the doors is a dead battery. The coin cell battery in the key fob is likely to drain quickly when you don't utilize it frequently enough. If your remote is beginning to show signs like a loss of range or has stopped functioning, then the battery may be dead.

Metal clips hold the battery in in the key fob. If the clips aren't tight, they can cause problems with contact that can prevent your remote to receive power. Use a flathead screwdriver to remove the retaining clip and remove the old battery. Be sure to use an alternative battery that has the same type of voltage, dimensions, and specification as the original battery.

The key fob can also become corroded or damaged by exposure to water. Even a quick bath in soapy water could harm the electronic chip in. It is best to keep your key fob in a dry area.

Water Damage

Water damage could be the reason behind your key fob not functioning properly. Key fobs come with rubber seals to protect them from being damaged by a light rain or splashes of water, but it is very important to keep your car keys away from the pool, ocean, and washing machine!

The key fob contains an electronic chip which sends a message to the immobilizer system of your vehicle. This is the reason why your 500 can start or lock, but when the chip becomes wet, it will no longer work.

You can try cleaning the inside of your key fob's electronics with isopropyl Alcohol or an electronic cleaner to determine whether they're still functioning. It is recommended to replace a key fob in the event that it is submerged in salt water, rather than trying to fix it yourself.

A replacement fob may cost you a few dollars, but it's a lot cheaper than having to have your Fiat 500 towed to a dealer and fixed there! In addition, you can make it yourself in just only a few steps. Be sure to use the correct type of battery before you attempt to open your key fob. This task is more straightforward than it appears and you can find step-by-step instructions online for almost any car key fob.

Faulty Chip

The chip in the key fob communicates to your vehicle's immobiliser to ensure that the vehicle is only able to start when the correct key is inserted. If the chip is damaged or vehicle destroyed the car won't start, no matter what you do.

Damage to the water or a dead phone battery are among the most frequently cited reasons for the chip being damaged. It is best to hand over the task to a professional locksmith who can repair the chip quickly and at an affordable price.

If your key fob does not work after exposure to clean tap or rain water take it off the battery. Wipe down the electronic component with paper towels. If the key fob will not work, there is the possibility that it's damaged components and requires to be replaced.

Some people go to their dealer if they require a new Fiat fob. But, this can be costly. If you are seeking a cost-effective solution to have your Fiat key fob repaired, look no further than United Locksmith. We have the tools and expertise needed to repair your Fiat key fob in a quick and professional manner.

Faulty Receiver Module

Fiat key fobs send an electrical signal to the vehicle that will unlock and close doors (and start the car for vehicles with an automatic transmission) up to 50 feet. There are many reasons why the fob may stop working. These include a dead coin battery, water damage buttons, worn out buttons as well as a receiver module problem and signal interference, or an electronic chip that has failed.

If the fob was located in the pocket that has been subject to severe trauma (such as being dropped on a hard floor or being washed in the washing machine) the fob might not be able to communicate with the Body Control Module (BCM) of the vehicle. The BCM is a security device that can only accept signals from genuine original keys.

You will need to replace the fob in case this happens. A professional locksmith can handle all aspects of the key replacement procedure as well as programming a new one for the 500. They can even give you the fob cloned to work exactly the same way as the original (and costs just a fraction of what it would cost).