How to Replace a Hyundai I10 Key Fob Battery

The Hyundai i10 is among the most elegant and stylish cars available. Its interior is of higher quality than its rivals such as the Citroen C1, Volkswagen UP and SEAT Ibiza.

Hyundai's key fob performs lots of work for you, including locking and unlocking your vehicle remotely. It also includes a mechanical key that is able to be used in the event the battery of your fob dies.

Dead Coin Battery

Key fobs allow drivers to lock their cars and start them without having to insert an actual key into the ignition. This is accomplished by radio frequency signals which communicate with the computer onboard of the vehicle.

The battery inside the keyfob is responsible for communicating. It will eventually get worn out, and will need to be replaced. Depending on the Hyundai model, you may or may not get a warning when the battery is nearing the end of its life. It's best to keep a spare key fob with you to quickly replace the battery if it starts to wear out.

The key fob has to be programmed again to the car after the new battery has been installed. This can be done with an OBDII or Hyundai Digital Key scanner, but it is usually easier to do in your Reno home. To complete this task, follow the instructions in your owner's manual or search on YouTube for "how to open and change a Hyundai key fob battery." Make sure you record the old battery's code or take a photo of it prior to removing it.

After the key fob has been reprogrammed, it should begin working properly. If it's not working then you'll need to go to an agent for a replacement or call locksmith. They'll have the expertise and tools to fix it.

Water Damage

A key fob is an excellent piece of technology that allows you to lock your car from the safety of your home, roll down the windows from the outside and even begin the vehicle. However, it's not indestructible and will eventually wear out due to regular use. Fortunately, the process of replacing a Hyundai I10 key fob battery is fairly simple and cost-effective.

It's not unusual to drop your key fob in an puddle, a pool or even a washing machine. It can be rescued by taking action quickly. A wet key fob is bad for electronics. It could cause corrosion, short-circuits, and even failure.

The first step is to get rid of as much water as you can. Shake out any visible moisture by flipping the fob. You may also be able to put it on top of an electric radiator or a hairdryer to accelerate the process. After you have removed all moisture you can, place the fob in a warm area where it will continue drying out for a couple of days.

Then, you can open the fob in order to remove the battery that was in it. Most hyundai replacement key (www.themcwars.org) i10 keys have the same battery type as many quartz watches, and are extremely simple to replace. After replacing the battery, take a photograph or note the location of the battery before closing the fob.

Poor Battery Contact

It's possible that your key fob's battery is depleted. This is a common problem and typically the remote starts showing indications of trouble long before it gives up completely. Make sure that the clips made of metal are not corroded or loose. If they are, you can use a wirebrush along with the battery cleaning solution to clean them. Make use of a button-cell battery that has the same size, voltage and specifications as the original.

This could also be a sign that your alternator may not be functioning correctly. The alternator is the part that charges your battery while you drive. A malfunctioning alternator will drain the battery fast and cause the warning light to turn on.

You can determine if the hyundai i10 key replacement is affected by a quick voltage test. If the battery is functioning properly, there's a possibility that the problem is with the circuit board or some other component of the key fob. You can access the key fob by pressing a small metal tab, or button on either the back or front of the unit. After removing the cover put in the CR2032 and make sure to connect all the connections.

Reprogramming

Hyundai offers keyless entry in the majority of its models. This makes traveling between Littleton and Parker, CO, easier than ever. You can use an electronic remote to start your car, open the doors, and lock them. However, it's not indestructible and a damaged or broken key fob can cause problems. If your Hyundai keyfob isn't working it is possible to reset it so that it functions with your vehicle.

First, you must remove the battery. Typically, the button cell battery is contained within a tab made of plastic. If you open the tab to replace the battery, make sure to use the same size and voltage as the old battery.

Once the battery is replaced, close up the tab and replace the clips that hold it. Then test the key fob to see whether it's still functioning.

If the key fob doesn't work, it could be time to talk to an expert locksmith or dealer. A locksmith or dealer can cut a new key and remote for you, and can also program the key to work with your car. This service is usually paid for, but it's worth it if you want to keep your Hyundai key fob in good working order. They can also assist in locating the perfect Hyundai key fob to meet your needs.