How to Replace a Kia Sportage Replacement Key

The key of many Kia models comes with the keyless entry feature built in. This key usually resembles a remote control and can be replaced with a new one from an Kia dealer or locksmith.

Key fobs may stop working for several reasons, including a dead coin battery, worn buttons water damage, signal interference and a malfunctioning receiver module. Here are some suggestions on how to get your Kia Picanto Key Sportage replacement key to function again.

How to replace a remote key or a smartkey?

If your Kia comes with an intelligent key, remote key push to start key or regular metal non-transponder key, the battery in these keys will eventually need replacing. This is especially when the car displays a message that the smart or remote key has a low battery.

Luckily, it's an easy procedure. To replace the battery in the keyfob take out your mechanical key from the slit at the back of the fob. Then, pull the cover open. Inside the key fob there will be tiny screws that hold the battery in its place. Take out the old battery by detaching the screw with a small screwdriver. Install the new battery and then close the gap on the key fob.

When the key fob is equipped with an updated battery Test it by pressing the locks and unlock buttons. You're good to go if the doors lock and unlock as expected. You can now utilize the hands-free feature to lock and unlock your Kia when your fingers get cold or you need to do some errands in Brandon.

Note: Certain key fobs may need to be programmed (transponder chips or smart keys). This requires a special programming machine that only the dealer or automotive locksmith has access to. Other keys (non transponder keys made of metal) do not require programming. If you're looking to reprogramme your key, you'll need record the key code number on the tag for the key code.

How do I replace the battery?

If your Kia key fob is not responding when you press the lock or kia rio key Fob unlock button on the fob, it is a sign that the battery needs to be replaced. A low battery can also cause other issues, like the check engine light coming on or the engine not turning properly. It is quite simple to replace the key fob batteries by using only a few simple tools.

Before you begin the process be sure that your vehicle is off and that all doors are closed. Find the small, metal or plastic piece on the bottom of the key fob. Then, jiggle it until the key is released. You can then insert the key into the handle on the door of your driver to open your car.

To replace the key fob battery, take off the cover from the back and use a plastic bar tool to loosen the latch holding the black negative battery cable. Remove the old battery, and then position the new battery to ensure its "+" side is facing you, and the "-", negative side is facing the fob's electrical contacts. Avoid using too much force when pushing the new CR2032 into position to avoid damage or bending the metal contacts.

Once the new battery has been installed after which you turn the key fob off and then on in the ignition repeatedly until the door locks. Then, you can test your Kia key fob to check whether it's working again.

How can you replace the smart key

You can have a standard keyfob or a Smart Key depending on the model of Kia Sportage. The difference between them is that the smart fob has tiny mechanical key blade tucked inside it, while the standard fob doesn't. Both kinds of key fobs come with batteries inside which eventually needs to be replaced. Fortunately, this is quite simple and takes just two minutes.

Be sure to switch off your Kia and sit on a flat and well-lit surface prior to you begin. Be aware that the fob contains tiny parts that could fall in the event of a mishap.

The small release button is located on the lower backside. This will be either a circular button or a rectangular slot. After pressing this button mechanical key blade, it will appear and you can then open the key fob.

Once you have the key fob open then you can remove the old battery and replace it. The new battery is a CR-2032 that can be purchased online or at a local auto parts store. When you are done with the battery, you should be able to lock and unlock your car using your key fob - even if your engine isn't running!

How do I replace the mechanical key?

The Kia key fob is a wonderful convenience that allows us to lock and unlock our vehicle with the press of a button. But, as with all devices, it can have problems at times. Luckily, there are ways to solve these issues and ensure that our key fobs are in good condition over the long haul.

One of the most common problems is a low or dead battery. This can cause the fob to stop working completely or even to stop working intermittently. If this is what you are experiencing, replace the battery with an entirely new battery.

If this doesn't fix the problem you can try using a standard flathead screwdriver to open the fob's plastic casing. Be careful not to scratch any internal components or scratch the plastic. After the battery has been removed, replace it with a new one.

Close and open the door with the mechanical key. (Every kia car key programming fob comes with a spare mechanical key which will fit into the slot). Test the key fob to check that it's functioning correctly. If the fob still isn't working, contact an authorized locksmith or dealer to help resolve the problem. Make sure they cut you an emergency key that can work for all door and trunk cylinders to avoid lockouts in the future.