Repairs to uPVC Windows

uPVC is a fantastic option for modern homes. They are long-lasting, durable and easy to maintain. They are not susceptible to rot or rust like timber and aluminum.

It is important to clean and oil UPVC windows and doors regularly. This will help avoid unnecessary repair costs as well as improve the efficiency of energy.

1. Broken Glass

If the glass in your window is broken it can cause a huge deal of damage to your home, making it very dangerous and potentially fatal. It is essential to take the time to make sure that you are doing everything you can to ensure that your windows are in good condition.

Single-pane windows are relatively easy to replace, and they will usually fit into the frames of the past easily. However If windows with double glazing repairs panes are held in place by internal beading, it will be more difficult to take out the old panes and put in new ones. In this case it is essential to buy plastic spacers to help the new pane fit into the window frame.

Wearing eye protection and thick gloves is a must for anyone who plans to remove the glass yourself. You should also lay down a dropcloth before you begin working on the window panes, so that any shards of glass fall onto the fabric and not on the floor and could be trampled under.

It's a great idea to cover the gap with tape after the glass is removed. This will prevent drafts and water from entering your property until a professional comes out to fix the window. This will also act as a barrier, preventing any intruders to gain access into your home. If the gap between the window and the door is substantial, you may want to use security screens that has an opening. This will give you the best of both.

2. Sagging

Upvc is a long-lasting energy-efficient, cost-effective and economical alternative to timber sash windows. However, with time, they are susceptible to a range of issues, including sliding. A sagging window can cause problems with light, draughts and even security. If you find that your uPVC window is beginning to sag it is important to act swiftly to stop the issue from getting worse.

Repositioning the hinges could help fix a window that is sagging. To do this, you'll have to open the window to access the frame. You can then unscrew both the top and bottom hinges using a screwdriver, and then adjust them clockwise or counter-clockwise. Close your window to check the fit after you've relocated your hinges. If you're satisfied with the fit, you can tighten the screws to ensure they stay in the right place.

If you can't reposition the hinges, you may need to replace the seal. Rubber seals may dry out and lose their elasticity over time, which causes them to lose their tightness. If this happens, it's crucial to replace the seal as fast as possible so that your uPVC windows remain watertight and draught-proof.

uPVC handles may also loosen up. The majority of the time, this is caused by screws that have come loose over time. However, it can occur because the handle mechanism has worn out. It's a good thing that it's simple to fix a loose uPVC window handle yourself. First, you'll need to close the window and then perform an experiment fitting. The corners of the sash should align with the casing joint. If it isn't, you can make use of a screwdriver to loosen the handle and turn the mechanism back into its original position.

3. Water Leaks

If you're waking up to wet floors and damp walls each time it rains, it is important that you take action. The leaks of water through windows could cause structural damage to your home and affect your ability to regulate the temperature of your home. Most of the time, uPVC window leaks are caused by a lack or damage to the sealant.

This is a fairly simple fix and should be undertaken by any competent DIYer. Depending on how serious the issue is, old caulking may need to be removed. When it comes to uPVC repair, you should avoid over-caulking. This will make your Window repair more difficult to clean and decrease its energy efficiency.

Make sure that the drainage holes do not have debris inside them and ensure that the sill pan is properly angled to allow the water to drain from the window. In more extreme instances, you may need to replace the window.

Other signs of long-term water leakage include sills that are rotten and the appearance of black spots of mold on the walls near the window. This fungus thrives under humid conditions and can propagate quickly throughout the house.

It is also important to note that if the leakage originates from the glass of your double glazed windows, it's more likely to be an issue with the glass seal, rather than the frame or sagging. Again this can easily be repaired by a uPVC window specialist who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or loose and blow open with a breeze It could be the hinges that are at the fault. They can be easily replaced by any competent DIYer and can be done within a few minutes.

Like any mechanical part hinges will be damaged over time. The process of replacing a hinge on a window is essentially a very simple process but it can be simpler if you have someone to help hold the frame up.

Verify that the uPVC hinges are closed and open in the right direction. You can check this by looking for the arrows on each hinge. This indicates which way the window should be opened.

Window hinges that aren't working properly can be caused by incorrectly opening the window in a particular manner or because of inadequate installation at the factory. This can often be resolved by sending us a photo via our website and we will be happy to give you suggestions.

It is also important to grease the hinges regularly. Applying a light engineering lubricant on the hinges is a great method to accomplish this. We recommend using the lubricant that doesn't contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication can help the window to open and close more easily. It also helps prevent corrosion and reduce the risk of sticking. It is recommended to do this at least once a year. WD40 and other solvent-based lubricants should not be used as they can damage your upvc window repairs near me windows.

5. Draughts

Draughts can be caused by different factors. First, the hinges due to wear and tear could become misaligned. This causes gaps to develop where the sash meets the frame. This can be easily repaired by giving them good clean, but in the event that they are beyond repair it might be necessary to have them re-aligned or replaced. The interlock, which is located on the hinge side of the window and can be misaligned. Again, it may be possible to give them a clean but in certain cases, it may be necessary to have these replaced.

The second most frequent reason for draughts is window seals, these can become worn down or damaged over time and allow air to escape through the gaps. Replacing these with high-quality weatherstripping can help prevent draughts. Replace the windows made of Upvc with low-emissivity lenses. This will help regulate indoor temperatures, and reduce the risk of draughts.

Another, and most effective methods to reduce drafts is to use an draught excluder. These are usually fabric tubes which are filled with a sort of filler and can be positioned on the top of your windowsill. They will keep your home warm by blocking cold air.

With a little maintenance and repair windows made of upvc will continue to provide an excellent level of security and insulation for your home. However, it is important to recognize that all windows have a life span and eventually, they will reach an point at which it is more efficient to replace them than repair them. So, if you're having issues with your upvc windows, it is always best to seek professional assistance immediately.