Peugeot 208 Key Replacement

It is best to delegate the replacement of Peugeot keys 208 to auto locksmiths with the required equipment and expertise. They can make and program new keys faster than a dealership would and at a lesser cost.

If your key fob stopped locking or unlocking your doors it is likely due to a dead battery in the coin. There are also other reasons that the key might be malfunctioning.

Dead Coin Battery

A dead coin battery will prevent your Peugeot 208 from locking or unlocking, and won't start the engine. In this situation you'll need to make use of the alternative method for starting as described in your vehicle's owner's manual.

The spark plugs might also be worn out. The spark plugs are responsible for instigating the fuel which starts the engine. They only last for a certain amount of time. If they aren't utilized enough they will eventually fail.

Fortunately, there's an easy solution to this issue. The best option is to test the voltage of your car battery with a multimeter. If it's less than 11.5 Volts, then you need to replace it. It is also important to clean the contacts of the battery when it has corrosion. This can be accomplished by removing the rubber cover from the two battery terminals, and then using a wirebrush to eliminate any corroded battery parts. You should then reconnect the cables for the positive and negative poles.

Water Damage

If your 208 does not start and the battery hasn't fallen flat, it is time to look at the spark plugs. It could be that they are just overly filthy, making them unable to spark. The spark plugs can be cleaned in the workshop.

Peugeot cars use a key with a transponder compatible with the immobiliser. This ensures that only the right key is able to turn the engine. If the chip in the Peugeot key is damaged then it won't send the proper signal to the vehicle.

Water damage is the most common cause of this problem. This is especially prevalent in colder climates, where the vehicle could have been exposed to rain or snow. If this is the case, call a reputable auto locksmith who has all of the tools and equipment needed to reprogram the new key. They also have the latest technology and equipment needed to create a peugeot 308 key fob 208 smart key. The process shouldn't be more than 15 minutes.

Faulty battery contacts

Peugeot replaced the transponder chips with a new model that is based on electronic components mounted on a circuitboard. The new system is excellent in its initial state, but the circuit boards degrade over time and stop working properly.

This could prevent the immobiliser's function from being activated, meaning your vehicle won't be able to start. If this happens it's a good idea contact a Peugeot specialist or locksmith.

Another common issue is when the key fob battery starts to die, this causes the blade of the key to stop being able to feed into the lock. A locksmith for cars can replace the battery and cut a new blade for you, this is normally a quick fix.

Faulty Receiver Module

It could be that the receiver module is faulty when your peugeot key fob replacement key fob stops working after being dropped on the floor, exposed to a sudden downpour or accidentally washed. The receiver is responsible for sending radio frequency signals to the on-board computer that controls the central locking system of your Peugeot vehicle.

The key fob itself is fitted with rubber seals which prevent water from reaching the chip inside. The chip can be damaged by water in the event that it is exposed the water for an extended period of period of. Submerging the key fob in ocean water at the beach or throwing it into the pool could be particularly damaging due to the high salt content.

The module must be replaced if your Peugeot spare key is no longer working. This is only performed by a professional auto locksmith or Peugeot specialist. As opposed to other cars, Peugeot keys are protected by an immobilizer that is unique and requires the correct code for the start of the engine. This is why it is imperative that you should only trust the Peugeot locksmith to design and program the replacement.

Computer with a problem on board

The on-board computer in your Peugeot is responsible for a variety of the systems in the car, from airbags to power windows. When something goes wrong with these systems, they will usually display a code that indicates the issue. The code will be stored within the system until the problem is resolved. Usually, this will mean replacing the on-board computer.

One of the most frequent reasons for the light turning on is the loose or corroded connection in the airbag sensor. This could be due to wear and tear, aging, or exposure to moisture and salt. It is essential to have this issue addressed as quickly as possible, as an airbag that is not functioning properly could be risky in the event of an accident.

If you find a card not found error on your Peugeot key fob, the battery inside the key fob could be weak or dead. This will stop the key fob from sending a signal to deactivate the immobilizer in your vehicle. You can test this by pressing the unlock button on the key fob and then attempting to start your car. If this fails, the key battery must be replaced.