Repairs to uPVC Windows

uPVC windows are a great choice for modern homes. They are long-lasting, durable and easy to maintain. They don't rot or rust like aluminum and timber.

Cleaning and lubricating regularly UPVC windows and doors is crucial. This will help prevent costly repairs and improve energy efficiency.

1. Broken Glass

The broken glass in your windows could cause significant damage to your home and even be fatal. It is essential to take the time to ensure that you're doing all you can to keep your windows in good repair.

For single pane windows, it can be relatively simple to replace them, and the replacement will generally fit within the frame of the previous one easily. However when windows with double panes are held in place by internal beading, it will be more difficult to remove the existing panes and install new ones. In this situation you'll need to find some plastic spacers to assist the new pane to fit perfectly into the window frame.

Wearing protective eyewear and thick gloves is a must when you are planning to remove the glass by yourself. It is also a good idea to lay down a dropcloth before you begin working on the glass so that any fragments of glass fall on the fabric rather than on the floor where they could be trampled on and cause further damage.

It's a great idea tape the gap once the glass has been removed. This will stop drafts and water from getting into your home until a professional comes out to repair the window. It also acts as a barrier, preventing any intruders from getting access to your home. If the gap between the window and the door is substantial, you may need to consider an alarm system that includes windows. This will give you the best of both.

2. Sagging

Upvc is a long-lasting energy-efficient, cost-effective and economical alternative to timber sash window. In time, they could be affected by a variety of issues, including sagging. A window that is sagging can cause problems with light, draughts or even security. It's crucial to act when you realize that your uPVC windows are falling down.

Repositioning the hinges can help fix a window that is sagging. First, you'll need to open the windows so you can access the frame. Then, remove both the hinges on the top and bottom using a screwdriver, and then adjust them clockwise or counter-clockwise. Once you've repositioned the hinges, close your window and check for an appropriate fit. If you're happy with the fit, tighten the screws to ensure they stay in the right place.

If you are unable to reposition the hinges, you could need to replace the seal. Over time, rubber seals lose their elasticity and become dry and cause their tightness to decrease. If this happens, it's crucial to replace the seal as soon as possible to ensure your uPVC windows are watertight and safe from drafts.

uPVC handles could also loosen. This is typically caused by screws that have been removed over time, but it could be due to the handle mechanism getting worn out. Fortunately, it's easy to fix a loose uPVC window handle yourself. First, you'll need to close the window and then perform an initial test to ensure that it fits. The corner joints of the sash should align with the casing joint. If it isn't then you can use a screwdriver or a wrench to loosen the handle, and then reverse the mechanism back into its original position.

3. Water Leaks

If you're waking up to wet floors and mouldy walls every time it rains it is important that you take action. The leaks of water from windows do are not just a cause for destruction of your home's structure but also hinder your efforts to control the temperature in your home. Most often, uPVC window leaks are caused by damaged or missing sealant.

This is a simple fix that can be done by any DIYer who is competent. Based on the severity of the problem the caulking that was used up may require removal before a fresh layer can be applied. It is important to remember that when it comes to uPVC window repair Biggin Hill (navigate to this website) repairs you should not be tempted to 'over-caulk and then make the area more difficult to clean and reduce your energy efficiency.

It is essential to ensure that the drainage holes are free of debris and that the sill pan is angled correctly so that it drains away from the window. In more serious cases you might have to consider replacing the window.

Mold spots and rotted sills are another sign of water leakage. The fungus thrives in humid conditions and can propagate quickly throughout the house.

It is also important to note that if the leakage originates from the glass of your double-glazed windows, it's more likely to be a problem with the glass seal rather than the frame or sagging. A uPVC specialist can fix this problem by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or slack and blow open with ease, it may be hinges that are at the fault. They can be repaired by any DIYer who is skilled and are usually done within a few minutes.

Like any mechanical component hinges are prone to be damaged over time. It is very easy to change the hinges on a window but it's much simpler if you have someone to help hold the frame.

It is also worth checking that the uPVC hinges are opened and closed in the correct direction. You can check this by looking for the arrows on each hinge, this shows which way the window should be opened.

Window hinges that aren't working properly could be the result of incorrectly opening the window a certain way or due to inadequate installation at the factory. It is usually possible to fix the issue by sending us a picture on our website. We will be pleased to offer you suggestions.

It is also important to grease the hinges regularly. This can be accomplished by applying a light engineering oil on the hinges, we recommend using a solvent-free lubricant, such as the 3-in-one Multi-Purpose oil. Regular lubrication can allow the window to operate and close more smoothly. It can also lower the possibility of a window getting stuck and stop corrosion. This must be done at a minimum every year. WD40 and other solvent based oils are not recommended because they could damage parts of your uPVC window.

5. Draughts

Draughts can be caused by different causes. The hinges, also due to wear and tear can become misaligned, this can cause gaps to develop where the sash meets the frame. These can be easily repaired by giving them a thorough clean, however if they are beyond repair it may be necessary to have them aligned or replaced. The interlock may also become disaligned. This is located on the hinge's side, and might require to be cleaned. In some cases it might be necessary to replace the hinges.

The second most frequent cause of draughts is the window seals. These can become worn down or damaged over time and will allow air to escape through these gaps. This can be prevented by replacing them with high-quality weatherstripping. Replace the windows made of Upvc with low-emissivity lenses. This will help to regulate indoor temperatures, and reduce the possibility of draughts.

Another method of reducing the amount of draughts is to use a Draught-excluder. These are typically fabric tubes filled with a filler, which can be placed over your window repairs High Wycombe sill. They will help block out cold air and keep your home warm and cosy!

With a little maintenance and repairs windows made of upvc will continue to provide a great level of security and insulation for your home. It is important to remember that all windows will eventually get worn out and it could be more cost-effective to replace them instead of fixing them. So, if you're having issues with your upvc windows, it is recommended to seek help from a professional immediately.