UPVC Window Repairs

Upvc windows are energy efficient and aid in reducing heating costs. As they age, however, problems may arise that require to be addressed. This can include faulty hinges, handles or locks.

Wooden window repair can be fairly easy for DIY enthusiasts to complete themselves. It can also be much less expensive than a brand new replacement window.

Cracks

Cracks and breaks in windows made of uPVC can be a serious issue. Leaving them unrepaired can lead to water ingress and less effective protection against cold weather and even the potential for structural damage. It is important to find a local repair or builder that specializes in repairing uPVC frames and can demonstrate the skills, experience and equipment required to achieve the most effective results. This will ensure that your crack is repaired quickly before it gets any worse, and you won't have to replace your window unit or glass.

Small cracks in glass can be fixed by using a variety of DIY solutions. Super glue and masking tape are among the most popular products that can hold broken glass in place for a while. For cracks that are more extensive, the tape may need to extend past the crack on both sides to achieve the optimal results.

You can also make use of two-part epoxy to fix broken or cracked glasses. Hardware stores typically sell this product for about $10. Ensure that your workspace is prepared prior to mixing the epoxy and make sure you have the right equipment for the job, like a soldering iron.

If your upper or lower sash is hard to raise, it's likely because the cords on the sash weights are damaged. This is a simple fix that can be done using a ladder and a flathead screwdriver. A drip cap that is rotten can be easily replaced at home. Many home centers stock a drip caps that are rot-free and can be easily caulked or nailed to be fixed. Make sure that the glass of double-paned or triple-paned window isn't damaged. This is because the gases that fill the space between the panes are responsible for improving energy efficiency and should be retained and not released.

Water Leaks

If your uPVC window is leaking, this can cause damage to your home and result in costly repairs. Water leaks can also cause structural damage to your home and the growth of mold. To avoid damage, it's important to fix any problems caused by leaky windows as soon as possible.

A damaged sealant around window frames is a typical cause of leaks. Silicone caulking will restore the seal to its original state and stop leakage. Examine for gaps and cracks between the window frame and also the brick or stone wall surrounding your windows.

A blocked drainage hole or an issue with Flashing are two other typical causes of windows that leak. Make sure that the drainage holes have not been clogged or blocked, especially after a heavy downpour. It's also a good idea to inspect the flashing that runs around the top of your window and ensure it's sealed correctly.

It is also important to make sure that your drip cap isn't missing or rotten. A rotten or missing drip cap will allow water to enter the window from above, causing damage to your home's structure. Replacing the leaky drip cap isn't difficult. It's as easy as purchasing a new one, and then nailing it to the.

It's an excellent idea to have your windows checked for water-tightness with a professional. They can employ a specific tool to measure the water-tightness of your windows and ensure they meet the industry standards. If your windows fail the test, they will have to be replaced. This is a costly fix but it's worth it for the comfort and safety of your family.

Sagging

If your windows aren't closing properly it can cause many issues, such as drafts condensation, and an increase in energy bills. It could also mean that the windows were not installed correctly or the sealant has worn out. Fortunately, there are a few options to fix the problem.

To fix your window properly it is necessary to set up a workspace with ample natural light. Start by laying down newspaper or an old blanket to protect the flooring from any splinters or drips that might fall off the windows while you work.

You should also use a white cloth that has been soaked in a solution of water and detergent. This will prevent any color stains from appearing on your windows. When you're ready to begin working on your uPVC windows, begin by making a note of where the hinge channel should be placed. Then remove the channel from the frame and fill the screw holes using epoxy (for uPVC windows) or wood filler (if frames are made from wood). Be sure to scrape the filled hole smooth before it sets.

Install the hinge channel after the holes are filled. Be sure to center it on the window jamb and then drill the new screw holes approximately a quarter-inch from the original locations.

Then, take a measurement of the spindle that protrudes from the underside of your handle. You can either order an alternative or bring it to a hardware shop to find a suitable replacement. Remove the setscrew from the shaft. File it flat to allow the set screw to lock onto the shaft. Now your uPVC window should be closing smoothly.

Broken Hinges

If your uPVC window hinges have broken or are not functioning correctly and you are unable to open or close the window, it will be difficult to open or close the window. This could be a security risk and also prevent your home from staying warm or cold. It's easy to get an entirely new hinge for your uPVC windows. It is essential to select the right type for your windows.

This is because the hinges need to be the same width to fit inside the frame of the window. The most popular hinge for uPVC windows are standard 18mm or UPVC 15mm hinges for windows. There are also specialised hinges for wooden frames. The correct type of hinge can help you avoid common problems with your windows.

There are a variety of reasons your window hinges could have become stiff or loose. The hinges might not be tightened enough. You can check this by using a screwdriver to locate the friction screw that is at the end of the hinge and then loosen it. You can then adjust it by turning it either way.

If your UPVC window hinges are not working as they should, you can contact Preston Glass Fix for a quick repair. Our technicians will inspect the condition of your hinges and offer you advice on the best solution. We can replace hinges on windows, retension them or install new locking mechanisms to ensure that your UPVC Windows are safe and secure.

Faulty Locks

UPVC window locks and mechanism are an essential part of home security. they make it very difficult to open the window without breaking in. It can be a frustrating experience when a lock malfunctions, but you don't have to replace the entire window.

It's often an issue that is minor and could have been easily avoided with regular maintenance. This is why we suggest getting your uPVC windows checked regularly by our yearly maintenance package to reduce the chance of problems.

Modern uPVC windows have espagnolette locks that work by pushing the handle's nose across a wedge block and then turning the handle to close the lock. They are effective at locking the window, however when they are not maintained correctly, over time they may start to fail. We recommend that you lubricate them with WD-40 every couple of times a year.

If you notice that your uPVC windows aren't opening and shut as quickly as they used to or if the lock is not working properly it is likely that there is a problem with the gearbox that locks the window doctor frame. Accessing this can be tricky as it requires the removing of seals around the frame and removing the handle (be careful not to damage these).

A locksmith who specialises in UPVC repairs has the knowledge to identify the problem quickly and be able to replace the damaged gearbox for locking with an exact replacement. This is a fast and easy repair that can save you hundreds of dollars by avoiding the need to buy new windows.