Repairs to uPVC Windows

uPVC is a fantastic choice for modern homes. They are easy to maintain and are durable and long-lasting. They are not susceptible to decay or rust as timber and aluminum.

It is crucial to wash and oil UPVC windows and doors on a regular basis. This will reduce costly repairs and improve energy efficiency.

1. Broken Glass

The damaged glass in your windows could cause severe damage to your home and even be fatal. It is crucial to take the time to ensure that you are doing everything you can to keep your windows in good condition.

For single pane windows, it can be relatively simple to replace them, and the new window will usually fit inside the frame that was previously installed easily. If you have double-paned windows that are joined by internal beading, it will be difficult to remove and replace the panes that were previously in use. In this instance you'll need to locate some plastic spacers that assist the new pane to fit correctly into the window frame.

If you're planning to try to remove the glass panes yourself it is important to wear the proper safety gear such as gloves that are thick and protective eyewear. It is also recommended to lay down a dropcloth before you start working on the glass to ensure that any shards will fall onto the cloth rather than on the floor where they can be trampled upon and cause further damage.

Once the glass is removed, it's a good idea to seal the gap with some clear packaging tape or duct tape to block water and drafts from getting into the property until a professional is able to come out and repair the window. It also acts as an obstacle to stop criminals from getting into your home. If the gap between the door and the window is substantial, you may want to use an alarm system that has an opening. This will provide the best of both.

2. Sagging

Upvc windows and doors are a low-cost energy-efficient, durable and long-lasting alternative to timber sash windows. However, over time, they are susceptible to a range of problems including sliding. A window that is sagging can cause problems with light, draughts, and even security. If you notice that your uPVC window is beginning to sag it is important to act swiftly to stop the issue from becoming worse.

To repair a window that is sagging, you can try to reposition the hinges. To accomplish this, you'll need to open the window so that you can access the frame. Then, using an screwdriver, remove the hinges at the top and bottom and adjust them by turning them clockwise or counter-clockwise. Close your window to check the fit after you have relocated your hinges. If you're happy with the fit, tighten the screws until they stay in position.

If you can't reposition the hinges you may need to replace the seal. Rubber seals may dry out and lose their elasticity over time, causing them to loosen. It is crucial to replace your seal as soon as you can to ensure that your uPVC window waterproof and draughtproof.

uPVC handles could also become loose. This is typically caused by screws that have become undone over time, but it could be due to the mechanism of the handle getting worn out. Luckily, it's not difficult to fix the handle of a window that is loose yourself. First, you'll need close the window and then perform an initial test to ensure that it fits. The joints at the corners of the sash must align with the joint on the casing. If it isn't, you can use a screwdriver or a wrench to loosen the handle and then turn the mechanism back into its original position.

3. Water Leaks

If you wake up to wet floors and damp walls each time it rains it's crucial to take action. Windows that leak water do can not only cause destruction of your home's structure but also hinder your efforts to control the temperature in your home. Most of the time, uPVC window leaks are caused by a damaged or missing sealant.

This is an easy fix that can be done by any DIYer who has the ability. Depending on how serious the issue is, old caulking may have to be removed. It is essential to keep in mind that when it is about uPVC window repairs, you should avoid the temptation to "over-caulk' as this will only make the area harder to clean and could reduce the efficiency of your energy.

It is essential to ensure that the drainage holes are free of debris and that the sill pan is placed correctly so that it drains away from the window. In more extreme cases, you may need to replace the window.

Mold spots and rotten sills are other signs of water leakage. The fungus thrives in damp conditions and can spread quickly throughout the home.

It is also important to note that if the leakage is coming from between the glass of your double glazed window repairs glazed windows, it's more likely to be a problem with the glass seal, rather than the frame or sagging. It is also possible to be corrected by a uPVC window specialist who will replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or slack and open with a breeze It could be the hinges that are at fault. They can be easily replaced by any competent DIYer and are usually done within a few minutes.

Most households in the UK will have either top hung or side-hung uPVC windows that are hinged and, like all mechanical parts, they will wear out over time. The process of replacing a hinge on a window is an easy procedure, but it is simpler if you have someone to assist in holding the frame in place.

Verify that the uPVC hinges are open and closed in the proper direction. You can check this by looking for the arrow on each hinge. This indicates the direction in which the window repairs should be opened.

The issue could be caused by opening the window improperly or by a poor installation at the factory. Sending us photos via our website is often enough to solve the issue. We are always happy to give assistance.

It is also crucial to grease the hinges regularly. This can be accomplished by applying a light engineering oil on the hinges. We recommend using a solvent-free lubricant, such as the 3-in-one Multi-Purpose oil. Regularly lubrication makes the window easier to open and close. It can also reduce the risk of a window sticking and prevent corrosion. This should be done at least every year. WD40 and other solvent based lubricants are not recommended as they can damage the parts of your uPVC window.

5. Draughts

Draughts in Upvc windows can be caused by a variety of different things. The hinges can also become unbalanced due to wear, causing a gap where the sash meets frame. If they're beyond repair, it might be required to realign them. In addition, the interlock could be disaligned. This is located on the hinge's side and could require to be cleaned. In certain instances, it may be necessary to replace the hinges.

The seals may wear out or get damaged over time, allowing air escape. This can be avoided by replacing them with high-quality weatherstripping. Replace the windows made of Upvc with low-emissivity lenses. This will help regulate indoor temperatures and decrease draughts.

The final method to cut down on draughts effectively is by using a Draught-exclusion device. These are typically fabric tubes filled with a filler which can be placed over your window sill. They can keep your home warm by blocking cold air.

Your upvc windows can continue to provide excellent insulation and security in your home with regular maintenance and repairs. It is crucial to keep in mind that all windows will eventually get worn out and it may be cheaper to replace them than to repair them. If you are experiencing problems with your upvc windows, it is always recommended to seek help from a professional immediately.