UPVC Window Handle Replacement

It is easy to repair a broken window handle with the right tools. It is important to identify the kind of handle you have and the spindle's size before you purchase a replacement.

Older uPVC windows have cockspur window handles which have a spur that protrudes to lock over a cockspur wedge striker plate. These can be either right or left-handed and have to be replaced with the same handle.

What kind of lock or handle do you have? I have?

There are many upvc window locks and handles each with their distinct advantages and functions. The type of handle that you have will determine if your locking mechanism is efficient and if it's easy to open windows. With time and regular usage, the window handles made of upvc replacement window handles can become damaged or worn out, rendering them less effective and secure. In some instances they might even disappear completely. It is crucial to fix your window handles made of upvc when you see they are falling off. This will prevent potential break-ins and keep your home safe.

It is a good thing that replacing your window handles made of plastic is a simple task that can be completed by nearly everyone. You will need a few basic tools, but with the right knowledge, it is simple and should only take a few minutes. You will need to know the kind of handle or lock that you have on your window. This will allow you to choose the right replacement.

Inline Espagnolette Handles

These are the most commonly used kind of upvc handle and are usually located on the other side of your window. They have a flat design and have an opening that is connected to the locking mechanism on the window frame when it is turned. Inline upvc handles have a spindle that runs through the middle of the handle and into the window frame to operate the latch.

Cockspur Handles

These handles are usually found on older uPVC window frames and have an unusual hook-shaped design. Cockspur handles are fitted with a single screw that holds the handle to the window frame and are not as secure as other types of window handles.

Handles that can tilt and turn

The tilt and turn handles are different from other upvc handles in that they can be turned for opening the window, and then lowered into the window to allow air circulation. They have a 7mm spindle at the back and are available both in right and left-handed versions.

It is important to measure the spindle size when buying replacement handles made of upvc. Not all of them are the exact same size. Drop something in the middle of the hole to measure the length. This is the longest spindle length that will fit your window.

What is the spindle?

uPVC window handles work similarly like doors, turning the handle to operate an opening inside the frame. This unlocks the window to allow it to be shut and opened. The handles can become damaged, particularly if they're often used or are exposed to harsh conditions. This could mean that you have to replace your uPVC windows handles as they may not operate the window in a proper manner in the future.

There are many different kinds of uPVC handles that are available, comprising Espag, Cockspur and Spaded handle options. These handles are designed to fit into the uPVC frames in various ways. Each handle uses a specific spindle to secure the mechanism into the window. This is why it is essential to know the kind of handle you have installed on your uPVC window to find the right replacement for it.

You can check what type of uPVC handle you have by taking a look at the base of your handle. A snap-in cover should be over the screw that holds the handle's base in place. Once you remove this and you'll be able to see the screw that holds the base of the handle in position. After both screws are removed and you are able to remove the handle from the uPVC.

After you have removed the uPVC window handle, you will need to remove the old spindle from the locking mechanism. Take note of the length of the spindle. You'll need purchase a replacement with the same length as the original handle and locking device.

The most common issue with uPVC window handle problems is that the handle spindle gets worn out and cannot longer function properly with the locking mechanism. This can be caused by corrosion, damage from constant use or a loosening locking mechanism. If this occurs, you will need to replace both the window handle and the locking mechanism to restore the full functionality of your uPVC Windows.

How do I take off the handle that was previously attached?

Window handles can be damaged or broken over time. It is essential to repair them as quickly as you can to ensure your security. It is easy to replace a damaged or worn handle. The job can be completed in under an hour without the need for any special tools.

To remove the old handle, you first need to remove the screw that is located at the base of the handle. Once the screw is removed, the handle will be removed. There will be a second screw that is located at the bottom of the handle's base, and this can be removed too. When both screws are removed the handle can be removed completely from the base section of the window.

After removing the old handle and align the fixing holes of the new handle to the holes already present in the window frame. There might be a small cap or sticker on the new handle, so remove them if needed and then screw the handle in place. Once the handle is in place, it is essential to check that it works by turning the handle and ensuring that the lock mechanism activates.

Espag handles feature spindles that extend out of the handle and slots into the multipoint locking mechanism that is on the frame of the window. Cadenza windows glass replacement near me feature a blade with cutouts that fit into the lock mechanism. Cockspur handles are long and hang over the outer frame of the window or the transom bar crossmember.

Once you have the new handle in place, slide the spindle inside the lock inside the window and then tighten it down. Once the handle is firmly fixed then replace the snap-in cover and screw cap (if appropriate). When the handle is ready to use, open and close the window a few times to make sure that it functions correctly and securely.

How do I put in the new handle?

Changing your uPVC window handle isn't difficult, and the process is actually very simple. All you require is a screwdriver and a small amount of patience. First, make sure the old handle is unlocked. Then remove any screws that are visible. You can also replace them using screw caps. Once the handle is removed and you are ready to take a note of the length of the spindle that protrudes from the back of the handle. This is important as it will determine what kind of handle you will need to buy.

Espagnolette handles that are made of uPVC are the most well-known kind of handle. They have a spindle which is inserted into the handle and acts as an internal locking mechanism within the window frame. The handle opens the latch and allows the window to open. As time passes and with regular use, espagnolette handles may become damaged or impaired which is why it is essential to find an alternative.

Cadenza handles are a second type of uPVC window handle commonly used on tilt and turn windows. They have a protruding knife that is operated by a multi-point locking mechanism inside the window. They are usually more secure than handles made of espagnolette because they are only accessible from the inside. You can replace them using the same method that you would for espagnolette handles however, ensure that the new handle is angled and not flat.

After you have picked the correct handle, simply align the new handle with existing screw holes prior to fixing it with screws. After that, you should put the screw covers back on and test that your new handle is operating correctly. You can perform this by moving the handle back and forth from the locked position to the unlocked one a few time. If you have any issues, it might be beneficial to speak with a professional to determine if they can assist in resolving the issue. They can often advise you on the best way to resolve the issue in a speedy and effective way.