How to Replace a Kia Sportage Replacement Key

For a variety of Kia models keys, the key has a built-in keyless entry system. The key functions like a remote control and is exchangeable by a Kia dealer.

Key fobs can stop working for a variety of reasons, such as an empty coin battery, worn buttons, signal interference, water damage, and a defective receiver module. Here are some suggestions on how to get your Kia Sportage replacement key to work again.

How do you replace the remote key or smartkey?

The battery inside your kia picanto key replacement's smart key will eventually need be replaced, regardless of whether it's a remote, a push-to-start key or a regular key that doesn't contain an electronic transponder. This is particularly when your car displays a message indicating that the remote or smart keys aren't powered.

Luckily, it's a relatively simple process. To replace the battery in the key fob remove the mechanical key from the slit in the back of the key fob. Then break the cover. Inside the key fob will be a small screw that holds the battery in the correct position. Remove the old battery by detaching the screw with a small screwdriver. Insert the new battery and then close the cut on the key fob.

Test the key fob by pressing the lock and unlock buttons. If the doors unlock and lock according to your expectations, then you're in good shape! You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers feel cold or when you need to run errands around Brandon.

Note: Some key fobs (transponder chip or smart keys) may require their programming completed. This requires a particular programming machine that only the dealer or locksmith can access. Other keys (non transponder metal keys) are not required for programming. If you need to reprogramme your key, you'll need to write down the key code's number on the tag for the key code.

How do you replace the battery?

If the Kia key fob doesn't respond to pressing the lock or unlock button, it's likely that the battery is insufficient. A low battery may also cause other issues like the check engine light coming on or delayed engine cranking. Fortunately, replacing the battery on the key fob is a simple DIY project that requires only some basic tools.

Be sure to turn off your vehicle and shut all doors prior to beginning. Locate the small plastic piece on the bottom of your key fob and jiggle it until a metal key slides out. Then, you can insert this key into the handle on the door of your driver to open your car.

To replace the battery inside the key fob, you must remove the rear cover. Use a plastic pry tool to loosen the latch that holds the black negative cable. Remove the old battery and then position the new battery so that its "+" side is facing you and the "-", negative side is facing the fob's electrical contacts. Avoid using excessive force when pushing the new CR2032 into place to avoid breaking or bending the steel contacts.

Once the new battery is installed, turn the key fob off and on in the ignition repeatedly until the door locks. Then, you can test your kia picanto car key replacement key fob to determine whether it's functioning properly again.

How do you replace a keyless keys

You can have an ordinary keyfob or Smart Key based upon the model of Kia Sportage. The difference between these is that the smart key has the small blade of a key in it, whereas the standard fob doesn't. Both kinds of key fobs contain batteries inside that eventually will need to be replaced. This is a simple procedure that takes less than two minutes.

Before you begin before you begin, make sure that you are on a flat surface with good lighting and that your Kia is off. Also, keep in mind that there are small parts inside the fob that can fall out if not careful.

The release button for the small size is located on the lower backside. It could be a circular silver button or a rectangular slot. Once you press this mechanical key blade, it will be released and you will be able to open the key fob.

Once you have the key fob open, you can simply remove the old battery and replace it. The new battery is a CR-2032 that can be bought online or from your local auto parts store. After installation with the battery, you should be able to lock, unlock and start your car with your key fob, even if the engine isn't running!

How do you replace a broken mechanical key

The Kia keyfob can be a fantastic convenience which allows us to lock or unlock our car by pressing a button. But, as with all devices, it can have problems occasionally. Luckily, there are methods to troubleshoot these issues and ensure that our key fobs are in good working order in the long run.

One of the most common problems is a dead or dead battery. This can cause your fob to stop working or operate intermittently. If this is the case, try replacing the battery with a fresh new one.

If this doesn't solve the issue, try using a standard flat-head screwdriver to break open the fob's plastic casing. Be careful not to scratch any internal components or scratch the plastic. Once the battery is removed then replace it with a brand new battery.

When the new battery is installed, close and unlock the doors using the mechanical key (every key fob in the kia has an emergency mechanical key that will fit in the slot). Test the fob to make sure it's working as intended. If the device isn't working, call an authorized locksmith or dealer to help resolve the issue. Make sure they cut you an emergency key that can work in all the trunk and door cylinders in order to avoid lockouts again.