Repairs to uPVC Windows

uPVC windows are a fantastic choice for modern homes. They are durable, long-lasting and easy to maintain. They are not susceptible to get rotten or rusty like aluminum or timber.

Cleaning and lubricating regularly UPVC windows and doors is essential. This will reduce unnecessary repair costs and also improve energy efficiency.

1. Broken Glass

The broken glass in your windows can cause serious damage to your home and may even be fatal. It is essential to take the time to make sure that you're doing all you can to keep your windows in good condition.

For single pane windows, it is relatively easy to replace windows, and the new one is usually able to fit into the frame that was previously installed easily. If you have double-paned windows that are joined by internal beading, it is difficult to remove and replace the old panes. In this case it is essential to purchase plastic spacers in order to aid in fitting the new pane into the window frame.

If you are going to attempt to remove the window panes yourself it is important to wear appropriate safety gear such as gloves that are thick and protective eyewear. It is also recommended to lay down a dropcloth prior to you begin working on the window panes to ensure that any shards fall on the fabric and not onto the floor and could be trampled under.

It's a good idea to seal the gap after the glass is removed. This will keep water and drafts from entering your home until a professional comes out to repair the window. This will also provide an obstruction to prevent intruders from getting into your home. If the distance between the door and the window is large, you might prefer an alarm system that includes windows. This will give you the best of both.

2. Sagging

Upvc is a long-lasting, energy-efficient and affordable alternative to timber sash window. However, over time, they are susceptible to a range of problems including sagging. A window that isn't properly aligned can cause problems with light, draughts and even security. It's crucial to act as soon as you realize that your uPVC windows are sliding.

Repositioning the hinges can help fix a window that is sliding. To do this, you'll need open the window to access the frame. Then, you can remove the top and bottom hinges with a screwdriver and adjust them clockwise or counter-clockwise. Once you've adjusted the hinges, close the window and verify the fit. If you're happy with the fit, you can tighten the screws to ensure they stay in position.

If you are unable to reposition the hinges, you might need to replace the seal. Rubber seals can dry out and lose their elasticity with time, leading them to loose their elasticity. If this happens, it's important to replace the seal as quickly as possible to ensure your uPVC windows are watertight and draught-proof.

uPVC handles can also become loose. This is often caused by screws that have become undone over time, but it can be due to the mechanism of the handle getting worn out. Luckily, it's not difficult to fix the loose uPVC window handle yourself. The first step is to close the window and perform an initial test to ensure that it fits. The joint at the corners of the sash should be aligned with the joint on the casing. If it doesn't then you can use the screwdriver to loosen up the handle. Then turn the mechanism back into place.

3. Water Leaks

It is essential to take action if wake up every morning to find a smoky wall and wet floors. Leaks of water from windows can cause structural damage to your home and hinder your ability to control the temperature in your home. The most frequent reason for leaks in uPVC windows is that the sealant around the frame has been damaged or missing.

This is an easy fix that can be completed by anyone who is a DIYer with the skills. Depending on the severity of the problem the caulking used previously might need to be removed before a new layer is applied. It is crucial to keep in mind that when it comes to uPVC window repairs, you should not be tempted to 'over-caulk in order to make the area more difficult to clean and could decrease the efficiency of your energy usage.

It is important to check that the drainage holes are free of debris and that the sill pan has been angled correctly so that it drains away from the window. In more serious cases you may need to think about replacing the window repair.

Moldy sills and rotten ones are also signs of water leakage. The fungus thrives in humid conditions and can propagate quickly throughout the home.

If the leakage is occurring between the double glazed window repairs-glazed window, it is more likely that the problem is related to the seal, not the frame. Again this can easily be repaired by a uPVC window specialist who will replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or slack and blow open in a breeze It could be hinges that are at the fault. They can be replaced by any competent DIYer and are usually done within a few minutes.

Like any mechanical component hinges are prone to be damaged over time. Changing a window hinge is essentially a simple process but it can be simpler if you have someone to help hold the frame up.

Make sure that the uPVC hinges are open and closed in the right direction. Look for the arrows that are on each hinge to determine the direction in which the window should be opened.

The problem can be caused either by opening the window improperly or by a poor installation at the factory. Sending us photos via our website will often solve the issue. We are always happy to offer advice.

It is also essential to lubricate the hinges on a regular basis. Applying a light engineering lubricant to the hinges is a good way to do this. We suggest using a lubricant that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication can make the window easier to open and close. It can also stop corrosion and reduce the possibility of sticking. It is recommended to do this at least once a year. WD40 and other solvent-based lubricants should not be used as they can cause damage to your uPVC windows.

5. Draughts

Draughts can be caused by a variety of different causes. The hinges can also be unbalanced due to wear, causing a gap where the sash meets frame. If they're beyond repair, it may be necessary to get them re-aligned. The interlock, which is located on the hinge side of the window, can also become misaligned, again it is feasible to give them a thorough clean, however in some instances it could be necessary to have them replaced.

The next common cause of draughts is the window seals. These are prone to wear or damaged over time and let air escape through the gaps. Replacement of these with high-quality weatherstripping can help stop draughts. Replace the upvc windows with low-emissivity glasses. This will help regulate indoor temperatures and lessen the possibility of draughts.

One of the most effective ways to cut down on drafts is to use an draught excluder. These are typically made of fabric that are filled with some sort of filler and can be placed on the windowsill on top. They can keep your home warm by blocking out cold air.

With a little maintenance and repair windows made of upvc will provide excellent security and insulation for your home. It is essential to remember that all windows eventually get worn out and it could be more cost-effective to simply replace them rather than repair them. If you are experiencing issues with your Upvc window it is recommended to speak with a professional as soon as you can.