UPVC Window Handle Replacement

Replacing a broken window handle is a relatively easy task and with the right tools it can be done quite quickly. However, it is essential to know your type of handle and the spindle length before buying the replacement.

Older uPVC window handles have a spur which extends and is locked over the wedge striker. They can be right or left-handed and have to match when replacing.

What kind of lock or handle do I have?

There are a variety of windows locks and handles made of upvc each with its distinct advantages and functions. The kind of handle you choose will determine the ease to open your windows and whether or not the locking mechanism works as intended. With time and regular use, window handles made of upvc can become damaged or worn out, rendering them less secure and efficient. In some instances they could even fall off completely. It is crucial to fix the handles on your window made of upvc as soon as you see them falling off. This will stop potential burglaries and ensure your home is secure.

It's a task that virtually anyone can perform. With a few basic tools and the proper knowledge, this is a simple procedure that should take no more than a couple minutes. To get started you'll need to identify the type of lock and handle that you have on your upvc window, which will help you to find the ideal replacement.

Inline Espagnolette Handles

These are the most commonly used type of upvc handle and are usually located on the other side of your window. They are flat and come with an open latch that is connected to the locking mechanism of the window frame. Inline upvc handles have spindles that run through the centre of the handle and then into the frame of the window to activate the latch.

Cockspur Handles

These handles are typically found on older uPVC windows and feature an distinctive hook-shaped design. Cockspur handles have a single screw that is used to secure the handle to the window frame and are not as secure as other kinds of window handles.

Tilt and Turn Handles

In contrast to other handles made of upvc that are tilt and turn, these handles can be rotated to open the windows and turned inwards to allow to allow ventilation. Generally, they have a 7mm spindle on the back of the handle and are available in left and right handed versions.

It is important to measure the spindle size when buying replacement of window glass upvc handle. There are a few that are the exact same size. To test the length of your upvc handle simply drop something into the middle of the hole, and then measure how far down it goes before it reaches an obstruction. This is the length of the spindle that will fit in your window.

What is the spindle?

uPVC window handles function in a similar way like doors, turning the handle to open a latch inside the frame. The window then opens and closed. However, in some cases, these handles can become damaged, particularly if they are regularly used or exposed to harsh weather conditions. This could mean that you have to replace your uPVC handles for windows as they may not operate the window correctly in the future.

There are many types of uPVC handle options, including Espag, Cockspur, and Spaded handles. They are made in a variety of ways to fit into uPVC frames. Each handle style uses an entirely different spindle for locking the window mechanism. This is why it is essential to identify the kind of handle is installed on your uPVC window to get the correct glass replacement for windows for it.

The base section of the handle will inform the type of uPVC it is. A snap-in cover is over the screw that holds the base of the handle in place. After removing this you will be able to observe the second screw that holds the handle base in place. Once both screws have been removed, you should be able pull the handle from the uPVC.

Once you have removed your uPVC window handle, you have to carefully unscrew the old spindle from the locking mechanism. Take note of the length of the spindle. You'll need purchase a new one that is the same length as the handle that was originally used and the locking device.

The spindle wears down and becomes inoperable with the locking mechanism. This could be due to damage caused by constant use or loosening of the locking mechanism or even corrosion over time. If this happens, you'll need to replace both the window handle and locking mechanism to restore the full functionality of your uPVC Windows.

How do I take off the handle that was previously attached?

Through time and regular use, window handles may become damaged or broken and if this happens it is important to repair them as quickly as possible to ensure the security of your home. It is easy to replace a damaged or worn handle. The job can be completed in less than an hour without the need for any special tools.

To remove the old handle, you first need to remove the screw at the bottom of the handle. Once the screw is removed, the handle can be pulled away. A second screw is situated at the base of the handle. It can also be removed. After these two screws have been removed, the handle will be detached from the window's base.

After removing the handle, align the fixing holes of the new handle with the holes already present in the window frame. There might be a small cap or sticker on the new handle, so take off the caps if needed, and then put the handle in its place. Once the handle is set, it is essential to check whether it functions by turning the handle and making sure that the lock mechanism is activated.

Espag handles feature a spindle which protrudes out of the handle and slots into the multipoint locking mechanism on the window frame. Cadenza windows have an edge with cut-outs which slot into the lock mechanism while Cockspur handles have a long nose that is able to hook over either the frame's outer or transom bar cross-member within the window.

After you have installed the new handle, place the spindle into the window lock and tighten it. Replace the snap-in cover and screw cap (if appropriate) after the handle is fixed. The handle is now ready for use to use, so try opening and closing the window several times to make sure that it is working correctly and securely.

How do I install the new handle?

It's not difficult to alter the handle on your uPVC windows. The procedure is easy. All you need is a screwdriver and little bit of patience. The first step is make sure that the handle you have previously used is locked and then take out any screws that are visible, you can also replace them by screw caps if you need. After removing the handle, you need to make an note of the length of the spindle which protrudes from the back of the handle. This is important as it will determine what type of handle you need to purchase.

Espagnolette handles on uPVC are the most well-known kind of handle. The spindle is inserted into the handle to activate the locking mechanism in the frame of the window. Once the handle is turned it opens the latch on the window, allowing it to open. During regular use and over time, handles for espagnolette may become damaged.

Cadenza handles are another type of uPVC window handle commonly used on tilt and turn windows. They feature a protruding blade that operates an interlocking mechanism that is multipoint within the window. They are usually more secure than handles made of espagnolette because they are only accessible from the inside. They can be replaced by the same method as espagnolette handles, however you must ensure that the new handle has a curved blade as opposed to a flat one.

After you have chosen the right handle, simply align the new handle to existing screw holes prior to screwing it in place. You should then put the screw covers back on and verify that your new handle is operating correctly. You can do this by moving the handle between the locked position to the unlocked several times. It might be worthwhile to speak with an expert to determine whether you can solve any problems. They can offer advice on how to resolve the problem in a timely and effective way.