How to Replace a Hyundai I10 Key Fob Battery

The Hyundai i10 is one of the most elegant and stylish cars on the market. Its interior is better quality than rivals like the Citroen C1, Volkswagen UP and SEAT Ibiza.

Hyundai's keyfob does a lot for you. It can lock and unlock your car remotely. It also has a mechanical key, which you can use if the fob battery dies.

Dead Coin Battery

The key fob lets motorists to lock their vehicles and open them without needing to insert keys into the ignition. It does this through radio frequency signals that communicate with the car's onboard computer.

The battery inside the keyfob is the one responsible for communicating. It will eventually become worn out and it will have to be changed. Depending on the model of your Hyundai key fob, it could or may not display a warning before the battery has died. Keep a spare keyfob handy for you to replace the battery swiftly when it wears out.

The key fob has to be reprogrammed for the car once the new Hyundai Keys battery is installed. This can be done using the Hyundai Digital Key app or an OBDII scanner, however it's usually easier to do at your Reno home. To do this, follow instructions in your owner's manual or search on YouTube for "how to open and change the Hyundai key fob battery." Be sure you note down the old battery number or take a photo of it prior to taking it off. it.

After the key fob has been reprogrammed, it should work again. If it isn't working, you will need to go to an expert for a new key or contact a locksmith. They'll have the experience and tools to fix it.

Water Damage

A key fob is a useful piece of technology that lets you to lock your replacement car key for hyundai from the safety of your home, to roll down the windows from the outside and even start the vehicle. It's not durable and will eventually wear out with normal use. Fortunately, replacing a Hyundai key fob battery is simple and inexpensive.

The accidental dropping of your key fob into the pool, a puddle or even the washing machine isn't an uncommon occurrence and is often rescued, but only if you act swiftly. Water is a very bad mix when it comes down to electronics and a wet key fob can cause a myriad of issues, such as corrosion, short circuits and even complete failure.

The first thing you must do is try to squeeze as the most water out as you can. Flip the fob over and shake out any moisture that could be observed. You may also be able to place it on top the radiator or a hairdryer to accelerate the process. After you've removed all moisture you can, consider placing the fob somewhere that is dry and warm where it will continue to dry for some time.

The next step is to remove the fob, and then remove the battery that was in it. The majority of Hyundai key fobs with the i10 model use the same type of battery that's found in a variety of quartz watches. They are extremely simple to replace. After replacing the battery, you should take a picture or note the location of the battery before closing the fob.

Poor Battery Contact

It's possible that your keyfob's battery is depleted. This is a very common problem. Usually, the remote will begin to display signs of trouble before it completely fails. Check that the retaining clips are tight and do not have any corrosion on them. If so, use a wirebrush along with the battery cleaning solution to clean them. Use a button-cell battery that has the same size, New Hyundai Keys voltage and specifications as the original.

This could be a sign your alternator is not working correctly. The alternator is the component that charges your battery while you are driving. An inefficient alternator will draw the battery out quickly, causing the warning light to come on.

A quick test of voltage will aid in determining if this is the case with your Hyundai. If the battery is working there's a chance that the issue is on the circuit board or a different part of the key fob. You can access the key fob by pressing a small metal tab, or button on either the back or front of the device. After removing the cover then insert a CR2032 ensure that you contact all the connections.

Reprogramming

Hyundai provides keyless entry on all of its models. This makes traveling around Littleton and Parker, CO, easier than ever. You can use the remote to start your car, unlock the doors, and then lock them. But it's not impervious to destruction, and a broken key fob can cause issues. If your Hyundai key fob stops working, it may need reprogramming to work with your vehicle.

The first thing to take care of is removing the battery. The button cell battery is typically in a plastic tab. If you remove the tab to replace the battery, make sure to use the same size and voltage as the old battery.

Once the battery is replaced, close up the tab and replace the retaining clips. Test the key fob a second time to make sure it still functions.

If the key fob still doesn't work, it might be time to talk to a dealer or locksmith. A locksmith or dealer can cut a brand new key and remote for you, and can also program the key to work with your vehicle. They usually charge a fee to do this, but it's well worth the investment if you want your Hyundai key fob to to work. They can also help you choose the right Hyundai key fob to meet your needs.