Repairs to uPVC Windows

uPVC windows are a great choice for modern homes. They are easy to maintain, durable and long-lasting. Unlike timber and aluminium, they do not rust or rot.

Regularly cleaning and lubricating UPVC windows and doors is essential. This will reduce unnecessary repair costs and also increase energy efficiency.

1. Broken Glass

The damaged glass in your windows could cause significant damage to your home, and could even be fatal. It is important to take the time to ensure that you are doing everything you can to keep your windows in good shape.

For single pane windows it is fairly easy to replace windows, and the new one is usually able to fit into the frame that was previously installed easily. However, if you have double-pane windows that are held in place by internal beading, it'll be more difficult to get rid of the old panes and put in new ones. In this instance you'll need find some plastic spacers that assist the new pane to fit correctly into the window frame.

Wearing protective eyewear and thick gloves is essential when you are planning to remove the glass by yourself. It is also recommended to lay down a dropcloth prior to you begin working on the window panes to ensure that any shards fall on the fabric, not onto the floor, where they could be trampled.

It's a great idea to seal the gap after the glass is removed. This will stop water and drafts from entering your home until a professional comes out to repair the window. This also serves as an obstruction to prevent intruders from getting into your home. If the distance between the window and the door is large, you might need to consider a security screen that also includes a window. This will provide the best of both.

2. Sagging

uPVC windows and doors are a low-cost energy efficient, durable and long-lasting alternative to timber sash windows. However, over time, they may be afflicted by a variety of issues, including sagging. A sagging uPVC windows can cause problems with light, draughts, and even security. It's crucial to act immediately if you realize that your upvc window repairs windows are falling down.

To fix a sagging window you can try to reposition the hinges. To accomplish this, you'll need to open the window to get to the frame. With a screwdriver, you can take off the hinges on the top and bottom and adjust them by turning them clockwise or anti-clockwise. After you've repositioned the hinges, close your window and test it for fit. If you're satisfied with the size of the window, you can tighten screws to keep them in place.

If you are unable to reposition the hinges, you might have to replace the seal. Rubber seals can dry out and lose their elasticity over time, which causes them to loose their elasticity. If this happens, it's essential to replace the seal as soon as possible to ensure your uPVC windows are waterproof and safe from drafts.

uPVC handles may also become loose. The majority of the time, this is caused by screws that have come loose over time. However, it could also happen because the handle mechanism has worn out. It's a good thing that it's simple to fix the loose uPVC window handle yourself. You'll first need to close the window and then perform an initial fitting. The joint at the corners of the sash should be aligned with the joint on the casing. If it doesn't, you can make use of a screwdriver to loosen the handle, and then return the mechanism to its original position.

3. Water Leaks

It is important to take action if you wake up every morning to find mouldy walls and floors that are wet. Water leaks from windows can not only cause destruction of your home's structure but also hamper your efforts to control the temperature in your home. The most frequent reason for leaks in uPVC windows is that the sealant surrounding the frame is either damaged or not present.

This is a fairly simple fix that can be completed by any competent DIYer. Based on the severity of the problem the caulking used previously might need to be removed before a fresh layer can be applied. When it is time to uPVC repair, you should avoid over-caulking. This will make your window harder to clean and reduce its energy efficiency.

Make sure that the drainage holes are free of debris in them and ensure that the sill pan has been angled correctly to drain away from the window. In more extreme situations, you may have to replace the window.

Mold spots and rotted sills are also signs of water leakage. The is a fungus that thrives in damp conditions and can quickly spread across the house.

It is also important to keep in mind that if the leakage originates from the glass of your double glazed windows it may be more likely to be an issue with the glass seal rather than the frame or sagging. A upvc window repairs near me specialist can easily fix this issue by replacing the glass seal. This will ensure the complete insulation of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or slack and open with a breeze it could be hinges at the fault. These are easily repaired by any DIYer who is skilled and are usually done within a few minutes.

Like any mechanical component hinges are prone to be damaged over time. It's easy to replace a hinge on a window however it is easier if someone else helps hold the frame.

Check that the uPVC hinges are closed and open in the right direction. You can do this by looking for the arrow on each hinge, this indicates the direction in which the window should open.

The problem with the hinges on windows can be caused by incorrectly opening the window in a particular way or by inadequate installation at the factory. It is usually possible to fix the issue by sending us a picture on our website. We will be more than happy to give you suggestions.

Regularly lubricating the hinges is essential. This can be accomplished by applying a light engineering oil to the hinges, we recommend using a solvent-free lubricant such as 3-in-one Multi-Purpose Oil. Regular lubrication can help the window open and close more easily. It can also stop corrosion and decrease the chance of sticking. Ideally, you should do this at least once a year. WD40 and other solvent based fluids are not recommended since they could damage parts of your uPVC window.

5. Draughts

Draughts in Upvc windows can be caused by a variety of different things. The hinges, also due to wear and tear can become misaligned, this can cause gaps to develop where the sash joins the frame. If they're beyond repair, it could be required to realign them. Secondly the interlock, this is located on the hinge side of the window, can be misaligned. Again, it's feasible to give them a thorough clean, however in certain cases, it may be necessary to have these replaced.

The next common cause of draughts is the window seals. These can become worn down or damaged over time, and allow air to escape through the gaps. This can be avoided by replacing them with high-quality weatherstripping. Replace the windows made of Upvc with low-emissivity glasses. This will help regulate indoor temperatures and lessen the possibility of draughts.

Another, and most effective ways to cut down on drafts is to use a draught excluder. These are typically made of fabric that are filled with some sort of filler and can be positioned on top of your windowsill. They can help block out cold air and keep your home warm and cozy!

With a little regular maintenance and repair your windows made of upvc will continue to provide an excellent level of insulation and security for your home. It is essential to remember that all windows eventually become worn out, and it may be more cost-effective to replace them than to repair them. If you encounter any issues with your window made of upvc it is recommended to speak with a professional immediately.