Repairs to uPVC Windows

uPVC windows are a fantastic choice for modern homes. They are durable, long-lasting and easy to maintain. They do not decay or rust as aluminum and timber.

It is crucial to wash and oil UPVC windows and doors regularly. This will prevent unnecessary repair costs as well as improve the efficiency of energy.

1. Broken Glass

The damaged glass in your windows can cause serious damage to your home and even be fatal. You should take the time to make sure that your windows are in good working order.

Single-pane windows are fairly simple to replace, and they typically fit into old frames very easily. However when windows with double panes are anchored by internal beading, it'll be more difficult to get rid of the existing panes and install new ones. In this situation, it is necessary to purchase plastic spacers to aid in fitting the new pane into the window frame.

Wearing protective eyewear and thick gloves is a must if you plan to remove the glass yourself. It is also a good idea to lay down a dropcloth before you start working on the glass to ensure that any fragments of glass fall on the fabric instead of onto the floor where they can be trampled upon and cause further damage.

It's a good idea to tape the gap once the glass is removed. This will prevent drafts and water from getting into your home until a professional arrives to repair the window. It also acts as a barrier, deterring any intruders from getting access into your home. If the gap is particularly large, you may think about the security door with an integrated window as it will provide the best of both worlds.

2. Sagging

Upvc windows and doors are an affordable energy efficient, durable and long-lasting alternative to timber sash windows. However, over time, they may be afflicted by a variety of issues, including sliding. A window that isn't properly aligned can cause problems with light, draughts or even security. It's crucial to act when you realize that your uPVC windows are sagging.

Repositioning the hinges can aid in fixing a window that is sagging. To accomplish this, you'll need open the window so that you can get to the frame. After that, using a screwdriver, you can remove the hinges on the top and bottom and adjust them by turning them clockwise or counter-clockwise. Close your window to test the fit after having repositioned your hinges. If you're satisfied with the fit, tighten the screws to ensure that they remain in place.

If you are unable to move the hinges, you might need to replace the seal. Over time, rubber seals lose their elasticity and dry out, which causes them to lose tightness. If this happens, it's important to replace the seal as fast as possible so that your uPVC windows are watertight and draught-proof.

UPVC handles can also become loose. The majority of the time it is due to screws that have become loose over time. However, it could occur because the handle mechanism has been worn out. It's fairly simple to fix a loose uPVC hand. First, you'll need close the window and perform an experiment fit. The joint at the corners of the sash should align with the joint on the casing. If it does not, you can use the screwdriver to loosen up the handle. Then, turn the mechanism back into place.

3. Water Leaks

It is essential to act if you awake each day to find a smoky wall and floors that are wet. The leaks of water through windows could cause structural damage to your home and also impact your ability to regulate the temperature of your home. The most frequent reason for leaking uPVC windows is that the sealant around the frame is either damaged or is missing.

This is a fairly simple fix and should be undertaken by any skilled DIYer. Depending on the severity of the issue is, the old caulking might need to be removed. When it comes to uPVC repair, you should avoid over-caulking. This will only make your window harder to clean and reduce its energy efficiency.

Check that any drainage holes are free of debris inside them and that the sill pan has been angled correctly to drain away from the window replacement. In more severe instances, you may need to replace the window.

Mold spots and rotted sills are another sign of water leakage. This fungus thrives under damp conditions and can spread quickly throughout the house.

It is also important to note that if the leak originates from the glass of your double glazing repair glazed windows, it is more likely to be an issue with the glass seal, rather than the frame or sliding. Again this can easily be corrected by a uPVC window specialist who will replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or loose and blow open with a breeze, it may be the hinges that are at fault. They can be easily repaired by any DIYer who is skilled and are usually done within a few minutes.

Like any mechanical part hinges will be damaged over time. Changing a window hinge is an easy procedure, but it is simpler when you have a person to help you hold the frame in place.

It is also important to verify that the uPVC hinges are being opened and closed in the right direction. You can do this by checking for the arrows on each hinge. This indicates which way the window should be opened.

The issue can be caused either due to opening the window in the wrong way or a faulty installation at the factory. This issue can be fixed by sending us a photograph through our website and we will be happy to give you advice.

It is also important to grease the hinges regularly. This can be done by applying a light engineering oil on the hinges, we recommend using a solvent-free lubricant, such as 3-in-one Multi-Purpose Oil. Regular lubrication can help the window to operate and close more smoothly. It also decreases the chance of windows sticking and prevent corrosion. This must be done at a minimum every year. WD40 or other solvent-based lubricants should not be used as they can cause damage to your uPVC windows.

5. Draughts

Draughts in windows made of upvc can be caused by a variety of different factors. First, the hinges due to wear and tear can become misaligned, this will cause a gap to form where the sash meets the frame. If they are damaged beyond repair, it may be necessary to get them re-aligned. The second is the interlock, which is on the hinge side of the window Doctor, can also be misaligned, and again it is feasible to give them a good clean, but in certain cases, it may be necessary to have these replaced.

These seals are susceptible to wear and tear or be damaged over time, allowing air escape. This can be avoided by replacing them with high-quality weatherstripping. Replace the upvc windows with low-emissivity lenses. This will help to regulate indoor temperatures and lessen the possibility of draughts.

The last way to reduce the amount of draughts is to use a draught-excluder. These are usually made of fabric tubes filled with a filler that can be placed over your window sill. They can help stop cold air from entering and keep your home warm and cosy!

With a bit of regular maintenance and repairs windows made of upvc will provide an excellent level of security and insulation for your home. It is crucial to keep in mind that all windows eventually wear out and it is more cost-effective to simply replace them instead of fixing them. If you are experiencing issues with your window made of upvc you should consult a professional as soon as possible.