Repairs to uPVC Windows

uPVC is a fantastic choice for modern homes. They are long-lasting, durable and easy to maintain. They do not rot or rust like aluminum and timber.

It is essential to clean and oil UPVC windows and doors regularly. This will save you from costly repairs and improve energy efficiency.

1. Broken Glass

The broken glass in your windows can cause severe damage to your home and even be fatal. It is essential to ensure that your windows are in good working order.

For single pane windows, it is fairly easy to replace windows, and the new one will generally fit within the frame that was previously installed easily. However, if you have double-pane windows that are held in place by internal beading, it'll be more difficult to remove the old panes and put in new ones. In this instance you'll need source some plastic spacers that assist the new pane to fit correctly into the frame of the window.

Wearing eye protection and heavy gloves is essential if you plan to remove the glass by yourself. It is also recommended to lay down a drop cloth before you begin working on the window panes, so that any shards fall onto the fabric, not onto the floor, where they could be trampled under.

After the glass has been removed from the window, it's best to seal the gap with clear packaging tape or duct tape to stop drafts and water from entering the property until a professional is able to come out and repair the window. This also serves as an obstacle to stop intruders from making their way into your home. If the gap is large, you may be interested in a security door that has an integrated window as it will provide the best of both worlds.

2. Sagging

uPVC is a durable, energy-efficient and affordable alternative to timber sash window. However, with time, they may be afflicted by a variety of issues like sliding. A sagging uPVC window can cause issues with light, draughts, and even security. If you notice that your uPVC window is beginning to sag it's important to act quickly to prevent the problem from worsening.

Repositioning the hinges could aid in fixing a window that is sliding. To accomplish this, you'll have to open the window so that you can access the frame. Then, using the screwdriver, you'll be able to unscrew the hinges on the top and bottom and adjust them by turning them clockwise or anti-clockwise. Once you've repositioned the hinges, shut your window and test it for fit. If you're satisfied with the fit of your window doctor near me, you can tighten screws to hold them in place.

If you are unable to reposition the hinges, you may require replacing the seal. Rubber seals may dry out and lose their elasticity with time, leading them to loose their elasticity. It is crucial to replace your seal as soon as you can to keep your uPVC window watertight and draughtproof.

UPVC handles can also loosen. The majority of the time, this is caused by screws that have become loose over time. However, it can also happen because the handle mechanism has been worn out. It's relatively simple to fix a loose uPVC handle. First, you'll need to close your window and do an experiment to ensure that it fits. The corner joints of the sash need to be aligned with the casing joint. If it isn't, you can use a screwdriver to loosen the handle, and then turn the mechanism back into position.

3. Water Leaks

It is crucial to act if you wake up every morning to find a smoky wall and wet floors. Windows that leak water do are not just a cause for degradation of your home's structure but also hamper your efforts to regulate the temperature inside your home. Most often, uPVC window leaks are caused by damaged or missing sealant.

This is a fairly simple fix that can be done by any skilled DIYer. Based on the severity of the problem the caulking used previously may require removal before a new layer of caulk can be put on. When it is time to uPVC repair, it is important to be careful not to over-caulk. This can make your window replacement near me harder to clean and lower its energy efficiency.

Make sure that the drainage holes have no debris inside them and that the sill pan is angled correctly to drain away from the window. In more serious instances, you may need to think about replacing the window.

Other indicators of water leakage are rotted sills and the appearance of black spots of mold on the walls near the window. This fungus thrives under humid conditions and can propagate quickly throughout the house.

If the leakage is occurring between the double-glazed glass it is more likely the problem is with the seal rather than the frame. Again this can easily be corrected by an uPVC window expert who can replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or are loose and open in a breeze It could be the hinges that are at fault. These are easily repaired by any skilled DIYer and are usually done within a few minutes.

Like any mechanical part hinges will wear out over time. It's easy to replace a hinge on a window but it's much simpler if you have someone to help you to hold the frame.

It is also important to ensure that the uPVC hinges are opened and closed in the right direction. Look for the arrows on each hinge to determine the direction in which the window should be opened.

Window hinges that aren't working properly can be caused by incorrectly opening the window a certain manner or because of inadequate installation at the factory. Sending us a photo via our website is often enough to resolve the problem. We are happy to offer suggestions.

It is also important to ensure that the hinges are lubricated regularly. This can be done by applying a light engineering oil to the hinges. We suggest using a solvent-free lubricant, such as the 3-in-one Multi-Purpose oil. Regularly lubrication will help the window to open and close more easily. It also helps prevent corrosion and reduce the risk of sticking. This should be done at least once a year. WD40 and other solvent based oils are not recommended because they could damage parts of your uPVC window.

5. Draughts

Draughts in upvc windows can be caused by different things. The hinges, also due to wear and tear may become displaced, which will cause a gap to form where the sash meets the frame. They can be repaired by giving them a good cleaning, but when they're beyond repair, it may be necessary to have them aligned or replaced. The interlock may be misaligned. This is located on the hinge's side and might require to be cleaned. In some instances it is possible to replace these.

These seals are susceptible to wear and tear or be damaged over time, allowing air to escape. This can be prevented by replacing them with high-quality weatherstripping. Another option is to replace the upvc window with glass that is low-emissivity, which will help regulate indoor temperatures, and also reduce the risk of draughts.

The final method to cut down on drafts effectively is to use a Draught-exclusion device. These are usually made of fabric tubes filled with a filler, which can be hung over your window sill. They can keep your home warm by blocking cold air.

With a little maintenance and repairs your windows made of upvc will continue to provide an excellent level of security and insulation for your home. However, it is important to recognize that windows last for a certain period of time and there may come a point where it is more economical to replace them than repair them. If you have any problems with your Upvc window, it's best to consult an expert as soon as you can.