Reasons Why Your Nissan Qashqai Key Fob Won't Work

The Qashqai's bigger dimensions give it a distinct SUV-like feel. Its 19-inch alloy wheels on Ti and STL versions may also be firm. The front tyres of the Qashqai are also prone to losing traction on rough surfaces, and the CVT may occasionally display a wrist-flexing torque steering.

It is usually caused by a dead coin battery which can be easily replaced in just a few minutes. Be sure that the replacement battery is of the same voltage, size, and specification.

Water Damage

One of the most common reasons a Nissan key fob will give the "key ID is not correct" message is due to water damage. The rubber seals on the key fob are designed to protect the chip's electronics, but prolonged moisture exposure can cause it not to work properly. It's normal to see this when your key fob has been dropped into the ocean or swimming pool. But it can also occur when it becomes wet from the rain or soapy hands.

If your key fob has been exposed to water over the course of a long time, you may need to clean it with isopropyl or electronic cleaner. It could also have to be sent to a specialist to repair or replace it.

If your key fob requires to be replaced, it is an easy process. Make sure you have the correct multipack (CR2032, 3V). Then, you can open the front and back cases with an abrasive screwdriver. Remove the clips made of metal, then remove the battery, and then replace it. After reassembling the fob, put the mechanical key back into its place and make sure it functions as intended. If not, you will need to take it to your local Nissan dealer or a professional auto locksmith to repair the chip on the key. The chip is usually not damaged by water, so it should not cost a lot.

Dead Coin Battery

The coin battery is another common reason that your Nissan Qashqai remote key fob might not work. These batteries usually last 3-5 years but can go bad over time, particularly if the fob is frequently dropped. You could try replacing the battery with a new one but be sure it's the same voltage and size as the original. If you choose to use an alternative battery, it could cause the key to have an incorrect key ID which could prevent it from paired with your vehicle.

The best method to replace the coin battery on the Nissan Qashqai key fob is by opening the fob with the small screwdriver with a flat-head. The screwdriver should be put into a small hole on the bottom of the key fob. Gently twist the screwdriver to split the two halves. Then, remove the old CR2025 button cell battery and insert a new one after noting its position in the fob.

Examine the terminals to see if there is water damage or dirt before installing the new battery. If there is, wash the terminals using a small amount of isopropyl alcohol. Make sure that the pole cables are properly connected. They must be connected to the negative and the positive poles of your battery.

Troubleshooting

If your nissan key replacement Qashqai's primary fob doesn't function after being exposed to clean tap or rain water it could be a sign there's a problem with the internal chip. Change the battery won't fix this issue, and you'll have to buy a new key fob. If the key fob didn't work after you dropped it, it is likely that the chip inside was damaged. You can usually get the key fob back to work once again if it is removed and clean the chip with alcohol and paper towels and then insert it back into.

A common error that you might see on the dashboard of your car is "Key ID Not Correct." This means that the car is unable to recognize the key fob, and will not allow it to start the engine. The issue could be caused by several things such as water damage, undetectable malfunctions in the key fob's circuitry or RFID interference.

If the battery that powers 12 volts in your key fob empty or isn't supplying enough electrical current, it will stop working. This will affect the Nissan Qashqai's remote keyless system central locking, as well as the ability to start the engine using the key fob. Check the battery in the key fob if you are not able to lock or unlock your door manually. You could also try reinstalling the battery to reset your transmitter.

Reprogramming

Unless the key fob has been submerged in salt water and is unable to return to life after a simple rinse with clean water. You might also try cleaning your electronic chip using isopropyl ethanol or an electronic cleaner. If these methods don't work it could be time to replace the entire key fob with a new one.

If your nissan key fobs Intelligent Key is still not functioning, there may be an issue with the connection between it and your car. To reconnect it, start by turning the key into the ignition but without starting the car. Continue this process until the hazard light flashes twice. Then, turn the vehicle off and take out the keys.

Open the fob compartment of your vehicle's fob compartment. It is typically located in a door jamb, on the handle on the driver's side, or under an armrest. Find the small "program" button and press it. Once the process has been completed, you should hear an audible sound.

It's time to put your Intelligent Key to the test. Take a step away from the car, and click all of the buttons on it. If the lights flash and the horn beeps, it means that the key is successfully linked to the Nissan. You can also test it near the Nissan.