How to Replace a Kia Sportage Replacement Key

The key of many Kia models comes with an entry system that is keyless into. This key usually resembles an remote control, and can be changed with a new one from a Kia dealer or a locksmith.

Key fobs may stop working due to a variety of reasons, including an empty coin battery, worn buttons or buttons, water damage, signal interference, and a defective receiver module. Here are some tips to assist you in getting your Kia sportage replacement key working once more.

How to replace the remote key or smartkey

If your Kia comes with an intelligent key, remote key push to start key or a regular non-transponder steel key, the battery in these keys will eventually need replacing. This is particularly true if your car shows a message that states the smart or remote keys are in poor condition.

It's an easy procedure. To replace the battery of the keyfob take out your mechanical key from the slit on the back of the fob. Then, you need to pry the cover open. Inside the key fob will be the small screw that holds the battery in its place. With a small screwdriver, take the screw off and remove the battery that was in place. Then, insert the new one and close the hole in the key fob.

Test the key fob by pressing the lock and unlock buttons. It's good if the doors lock and unlock as you expect. You can now utilize your Kia's hands-free lock/unlock feature when your fingers are cold or you need to run some errands in Brandon.

Not all key fobs might need to be programmed (transponder chips or smart keys). This requires a programing machine that is available only to the locksmith who works for the automotive dealer. Other keys (non transponder keys made of metal) are not required for programming. If your key needs to be programmed, you must be aware of the number that is stamped on the tag that identifies the key and save it in a secure location.

How do you replace the battery?

If the 2013 Kia Optima key key fob does not respond when you press the lock/unlock button, it's a sign that the battery is insufficient. A battery that is not functioning properly can cause other issues, like the check engine light appearing or the engine not running properly. Fortunately replacing the key fob battery is a relatively easy DIY project that requires only a few tools.

Before you begin be sure that your vehicle is off and all doors are shut. Find the small, metal or plastic piece on the bottom of your key fob and gently jiggle it until the metal key slides out. The key can be put into the door's driver handle to unlock your car.

To replace the key fob battery, take off the cover from the back and use a plier bar tool to release the latch holding the black negative battery cable. Remove the old battery and then position the new battery to ensure its "+" side faces you and the "-" negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position, avoiding excessive force to avoid bending or damaging the contacts made of metal.

Once the new battery has been installed and the key fob is turned on, turn it off and then on in the ignition repeatedly until the door locks. You can then test your Kia's keys fob again to make sure it's working as intended.

How to replace the smart key

Depending on the model of the Kia Sportage, you may have the standard key fob, or a smart key. The difference between these is that the smart key comes with tiny mechanical key blade that is hidden inside, while the standard key fob does not. Both key fobs come with a battery that will eventually require replacing. This is a simple procedure that takes just two minutes.

Before you begin it is essential to ensure that you are on a flat surface with adequate lighting and that your kia soul key fob replacement is off. Keep in mind that the fob can contain small parts that can be thrown off when you're not careful.

The first step is to locate the small release button on the lower backside of the fob. It could be a circular silver button or a rectangular slot. You can open the key fob by pressing the button.

Once the key fob is opened, remove the battery that was in it. The new battery is a one called CR-2032 and can be bought on the internet or at your local auto parts store. After installation you should be able to lock, unlock and start your car using your key fob - even if your engine isn't running!

How do I replace the mechanical key

The Kia keyfob is a wonderful convenience which allows us to lock or unlock our car by simply pressing the button. Like any other device it may have issues occasionally. Luckily, there are ways to resolve these issues and keep our key fobs in good condition for the long run.

One of the most frequently encountered problems is a weak or dead battery. This could cause your device to stop working or operate intermittently. If this happens, try replacing the battery with a new kia key fob one.

If this doesn't fix the problem Try using a standard flat-head screwdriver to break open the fob's plastic casing. Be cautious not to damage any internal components or scratch the plastic. Once open, carefully remove the old battery and replace it with a brand new one.

When the new battery is installed, close and unlock the doors using the mechanical key (every Kia fob has an emergency mechanical key that can fit into the slot). Test the key fob to verify that it's functioning correctly. If the fob still isn't working, contact an authorized locksmith or dealer to resolve the problem. Make sure they make you an emergency key that functions in all the door and trunk cylinders to avoid lockouts again.