How to Replace a Kia Sportage Replacement Key

For many Kia models keys, there is a built-in keyless entry system. This key typically resembles a remote control and can be exchanged with a new one from a Kia dealer or a locksmith.

Key fobs can stop working due to a variety of reasons, including the battery being dead, worn-out buttons signals, signal interference or water damage. Here are some suggestions on how you can get your Kia Sportage replacement key back to working.

How do you replace a smartkey or remote key?

The battery in your Kia's intelligent key will eventually have to be replaced, regardless of whether it's a remote, a push-to-start key or a standard metal key that doesn't contain transponder. This is particularly relevant if your car displays a message indicating that the smart key or remote is not powered by the battery.

It's a simple procedure. To replace the battery in the keyfob, remove your mechanical key from the slit that is located at the back of the fob. Then, you need to pry the cover off. Inside the key fob will be a small screw that holds the battery in the correct position. Take out the old battery by unscrewing the screw with a small screwdriver. Insert the new battery and then close the cut on the key fob.

Test the key fob by pressing the lock/unlock buttons. You're good to go If the doors lock and unlock as expected. You can now make use of Kia's hands-free lock/unlock function when your fingers start to get cold or you have to go on errands around Brandon.

Note: Certain key fobs (transponder chip or smart keys) may need to have their programming completed. This requires a programming machine which is available to the automotive locksmith or dealer. Other keys (non transponder metal keys) do not require programming. If your key has to be reprogrammed, you will need to be aware of the key code that is stamped on the key code tag and keep the number in a secure place.

How do I replace a battery

If your Kia key fob is not responding to pressing the lock or unlock button on the fob, this is a sign that the battery should be replaced. A low battery could cause other issues like the check engine light turning on or delayed engine cranking. Fortunately replacing the key fob battery is a relatively easy DIY project that requires only a few basic tools.

Before you begin the process ensure that your vehicle is turned off and all doors are closed. Find the small, metal or plastic piece at the bottom of the key fob. Jiggle it until the metal key comes out. The key can be put into the driver door handle to unlock your car.

To replace the battery on the key fob, remove the rear cover. Use a pry tool to loosen up the latch that holds the black negative cable. Remove the old battery and align the new one in a way that the "+" positive side is facing you, and the "negative" negative side is facing towards the fob's electrical contacts made of metal. Push the new CR2032 battery straight into position and avoid excessive force to avoid bending or damaging the contacts on the metal.

After installing the new battery after which you turn the key fob on and off in the ignition until the door locks cycle. Then, you can test your kia car key replacement key fob to check if it is working properly again.

How to replace a smart keys

You can have a standard keyfob or a Smart Key depending on the model of kia picanto spare key - i60Bm7tc0rxec.com, Sportage. The difference is that the smart key comes with a small mechanical key blade hidden within it, whereas the standard key fob does not. Both kinds of key fobs come with an internal battery which eventually needs to be replaced. It is a simple process that takes just two minutes.

Make sure to shut off your Kia and be on a flat or well-lit surface prior to when you begin. Be aware that there are tiny pieces inside the fob that can be removed if not careful.

The release button for the small size is located on the lower backside. It can be a circular silver button or a rectangular slot. When you press it the mechanical key blade will pop out and you can then open the key fob.

After the key fob has been opened, take out the battery that was in it. The new battery is a one called CR-2032 and can be bought online or in your local auto parts shop. Once you're done, your key fob will allow you to lock and unlock your vehicle, even if it isn't running.

How to replace the mechanical key?

The kia ceed key fob replacement keyfob is a wonderful convenience that lets us lock or unlock our car by pressing a button. But like any device, it can have problems occasionally. There are ways to address these issues and keep your key fobs functioning for a long time.

One of the most frequently encountered problems is a low or dead battery. The battery could cause the device to stop working or operate intermittently. If this is the case you should replace the battery an entirely new battery.

If this isn't enough to solve the problem, use the flathead screwdriver that is standard to wedge the fob's casing made of plastic open. Be careful not damage any internal components or scratch the plastic. Once the battery is removed, replace it with a new one.

Once the new battery is installed, close and unlock the doors using the mechanical key (every kia fob has an emergency mechanical key that can fit in the slot). Test the key fob and make sure it is working correctly. Contact a dealer, or a locksmith to solve the issue when the fob still is not working. Make sure they make you an emergency key that can work for all trunk and door cylinders, to avoid future lockouts.