Repairs to uPVC Windows

uPVC windows are a great option for modern homes. They are long-lasting, durable and easy to maintain. They do not get rotten or rusty like aluminum and timber.

Regularly cleaning and lubricating UPVC windows and doors is vital. This will reduce repair costs and improve energy efficiency.

1. Broken Glass

If the glass in your window is broken it can cause a great amount of damage to your home, which can make it very hazardous and possibly fatal. It is essential to ensure that your windows are in good condition.

Single-pane windows are relatively easy to replace and will usually fit into the frames of the past easily. However If windows with double panes are held in place by internal beading it will be more difficult to remove the panes that are in place and replace them with new ones. In this case, it is necessary to buy plastic spacers to aid in fitting the new pane into the window frame.

Wearing eye protection and thick gloves is essential if you plan to remove the glass by yourself. It is also recommended to lay down a dropcloth before you begin working on the glass so that any shards fall onto the fabric instead of onto the floor, where they could be trampled upon and cause further damage.

Once the glass is removed from the window, it's best to seal the gap with packaging tape or duct tape to block drafts and water from entering the home until a professional comes out and fix the window. It also acts as an obstacle to stop intruders from getting into your home. If the gap is large, you may want to consider using the security door repair with an integrated window as it offers the best of both worlds.

2. Sagging

uPVC windows and doors are a cost-effective energy-efficient, durable and long-lasting alternative to timber windows made of sash. However, over time, they are susceptible to a range of issues, including sagging. A sagging uPVC windows can cause problems with light, draughts and even security. If you find that your uPVC window is beginning to shrink, it's important to act quickly to prevent the problem from worsening.

Repositioning the hinges can aid in fixing a window which is sagging. To accomplish this, you'll need to open the window so that you can get to the frame. Then, remove both the hinges on the top and bottom using a screwdriver, and then adjust the hinges clockwise or counter-clockwise. Close your window to check the fit after you have relocated your hinges. If you're satisfied with the fit, tighten the screws to ensure they stay in the right place.

If you cannot reposition the hinges, you could have to replace the seal. Over time rubber seals can lose their elasticity and become dry which causes them to loosen. It is important to replace your seal as quickly as you can to ensure that your uPVC window watertight and draughtproof.

upvc door repairs near me handles may also loosen up. This is usually due to screws that have loosened over time, but it could also be due to the handle mechanism wears out. It's fairly simple to fix a loose uPVC handle. You'll first need to close the window and do a test fitting. The joints at the corners of the sash must align with the joint on the casing. If it isn't you can use a screwdriver to loosen the handle. Then turn the mechanism to position.

3. Water Leaks

If you awake to wet floors and damp walls every time it rains it's important to take action. The leaks of water from windows do not only lead to the destruction of your home's structure but also undermine your efforts to control the temperature inside your home. The most common cause for leaks in uPVC windows is that the sealant around the frame is damaged or missing.

This is a fairly simple fix that can be completed by any competent DIYer. Based on the severity of the issue the old caulking may require removal before a new layer of caulk can be put on. It is important to remember that when it is about uPVC window repairs you should not be tempted to 'over-caulk and then make the area more difficult to clean and can reduce your energy efficiency.

Make sure that the drainage holes are free of debris in them, and also ensure that the sill pan has been angled correctly to drain away from the window. In more severe situations, you may have to replace the window.

Other signs of long-term water leakage are rotted sills and the appearance of black spots of mold on the wall near the window. This fungus thrives in damp conditions and can spread quickly throughout the house.

If the leakage is occurring between the double-glazed glass, it is more likely that the problem is related to the seal, not the frame. A uPVC specialist can fix this issue by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

Hinges could be at fault for the reason that your uPVC window is difficult to open or it blows open with a breeze. Anyone who is a skilled DIYer can fix the hinges in a matter of minutes.

Nearly every home in the UK will have either top hung or side-hung uPVC windows that are hinged and, just like any mechanical component they will wear out over time. It's easy to change the hinges on a window, but it's easier if someone helps you hold the frame.

Make sure that the uPVC hinges are open and closed in the proper direction. Look for the arrows that are on each hinge to determine which way the window should be opened.

Window hinges that aren't working properly can be caused by incorrectly opening the window in a particular way or due to poor installation at the factory. Sending us photos via our website is often enough to solve the issue. We are happy to give assistance.

It is also essential to lubricate the hinges regularly. Applying a light engineering lubricant to the hinges is a great method of doing this. We recommend using the lubricant that doesn't contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication will make the window easier to open and close. It can also prevent corrosion and reduce the risk of sticking. Ideally, you should do this at least once a year. WD40 and other solvent-based oils are not recommended because they could damage parts of your uPVC window.

5. Draughts

Draughts in upvc windows can be caused by a few various factors. The hinges can also become disaligned as a result of wear, creating a gap where the sash meets frame. This can be easily repaired by giving them good cleaning, but if they are beyond repair it might be necessary to have them aligned or replaced. The interlock may also become unbalanced. This is located on the hinge's side, and could require to be cleaned. In some cases it might be necessary to replace these.

The second most frequent reason for draughts is window seals. They are prone to wear or damaged over time and allow air to escape through these gaps. This can be prevented by replacing them with high-quality weatherstripping. Replace the upvc windows with low-emissivity glasses. This will help regulate indoor temperatures, and reduce the possibility of draughts.

The final method to cut down on the amount of draughts is to use a Draught-exclusion device. These are usually fabric tubes filled with a filler, which can be put on top of your window sill. These will help to stop cold air from entering and keep your home warm and cozy!

Your upvc windows can keep providing excellent insulation and security to your home by performing regular maintenance and repairs. It is crucial to recognize that windows last for a certain period of time and eventually, they will reach an point at which it is more efficient to replace them than fix them. If you are experiencing issues with your Upvc windows, it is recommended to seek help from a professional immediately.