How to Replace a Kia Sportage Replacement Key

For a number of Kia models keys, there is a built-in keyless entry system. This key typically resembles the remote control and can be replaced with a new one from an Kia dealer or a locksmith.

Key fobs are prone to malfunction for several reasons, including batteries that are dead worn buttons water damage, signal interference and a malfunctioning receiver module. Here are some guidelines on how you can get your kia transponder key Sportage replacement key to function again.

How do you replace a remote key or a smartkey?

Whether your Kia is equipped with an intelligent key, remote key push to start key, or a regular non-transponder metal key The battery inside these keys will eventually require replacement. This is particularly relevant if your vehicle displays a message that indicates that the remote or smart key has a low battery.

This is a relatively simple procedure. To replace the battery of the keyfob, remove your mechanical key from the slit at the back of the fob. Then, pull the cover off. Inside the key fob, there will be tiny screws that hold the battery in the correct position. Take out the old battery by detaching the screw with the help of a small screwdriver. Then, insert the new and close the slit inside the key fob.

Test the key fob by pressing the lock/unlock buttons. If the doors lock and unlock according to your expectations, then you're all set! You can now use Kia's hands-free lock/unlock function whenever your fingers get chilly or you need to make errands in Brandon.

Note: Certain key fobs may need to be programmed (transponder chips or smart keys). This requires a special programming machine that only the dealer or automotive locksmith can access. Other keys (non transponder metal keys) are not required for programming. If you need to reprogramme your key, it is necessary to note the key code number on the key code tag.

How do I replace a battery

If the kia optima locked keys in car key fob does not respond to pressing the lock/unlock button, it's likely that the battery is insufficient. A weak battery can cause other problems like the check engine light coming on or delayed engine cranking. Fortunately, replacing the key fob battery is a simple DIY project that requires just a few basic tools.

Be sure to turn off your vehicle and close all doors prior to starting. Find the small metal or plastic piece on the bottom of the key fob. Then, jiggle it until the metal key comes out. You can then insert this key into the handle of the door for the driver to open your car.

To replace the key fob's battery, remove the rear cover and use a plier bar tool to remove the latch that holds the black negative battery cable. Take the old battery out, and then align the replacement battery to ensure its "+" side is facing you and the "-" negative side is facing the fob's electrical contacts. Avoid using excessive force when pushing the new CR2032 into place to avoid breaking or bending the steel contacts.

Once the new battery has been installed then turn the key fob off and then on in the ignition several times until the door locks. Then, test your Kia key fob to determine whether it's functioning properly again.

How do you replace a smart key

You may have either the standard keyfob or Smart Key, based on the model of Kia Sportage. The difference between these is that the smart fob has a small mechanical key blade hidden within it, whereas the standard fob doesn't. Both kinds of key fobs contain an internal battery that eventually will need to be replaced. Fortunately, this is an easy task that will take about two minutes.

Before you get started it is important to make sure that you are on a flat surface with adequate lighting and that your Kia is off. Be aware that there are small parts inside the fob which could be snagged if not vigilant.

The release button for the small size is located on the lower backside. It will be an oval or circular slot. You can open the key fob by pressing the button.

Once the key fob is opened, remove the battery that was in it. The new battery is a C2032, and can be bought online or in your local auto parts shop. When you are done, you should be able to lock and unlock your vehicle using your key fob even if the engine isn't running!

How do I replace the mechanical key

The Kia keyfob is a wonderful convenience that lets us lock or unlock our car simply by pressing a button. But, as with all devices it may have issues at times. There are solutions to fix these problems and keep your key fobs working for the duration of.

A low or dead battery is one of the most common issues. This can cause the device to stop working altogether or stop working at times. If this is the case, try replacing the battery with a fresh new one.

If this doesn't resolve the problem you can try using a standard flathead screwdriver to open the fob's plastic casing. Be careful not to harm any internal components or scratch the plastic. After the battery has been removed, replace it with a brand new one.

Close and open the door with the mechanical key. (Every 2013 kia optima key fob comes with a spare mechanical key that fits into the slot). Test the key fob and ensure that it's working properly. Contact a dealer or locksmith to address the issue if the fob is still not working. Make sure they cut you an emergency key that can work in all the door and trunk cylinders to prevent lockouts in the future.