How to Replace a Kia Sportage replacement kia key Key

The key of many Kia models has an electronic keyless entry system built in. The key can be compared to an remote control, and can be changed with a fresh one from a Kia dealer or a locksmith.

Key fobs can stop working for a variety of reasons, such as an empty coin battery worn buttons or buttons, water damage, signal interference and a faulty receiver module. Here are some tips to help you get your Kia sportage replacement key to work again.

How to replace the remote key or smartkey?

No matter if your Kia is equipped with an intelligent key, remote key push-to-start keys, or regular metal non-transponder key the battery in these keys will eventually require replacement. This is particularly the case if your car shows a message that states the remote or smart keys are in poor condition.

It's a fairly simple procedure. To replace the key fob battery take the mechanical key from the slit in the back of the key fob. Next, pry open the cover. A small screw is located inside the key fob that holds the battery in place. Remove the old battery by unwinding the screw with the help of a small screwdriver. Install the new battery and then close the opening on the key fob.

When the key fob is equipped with an updated battery and you've tested it, press the locks and unlock buttons. You're good to go if the doors lock and unlock as you expect. You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers become cold or you need to complete errands in Brandon.

Note: Some key fobs (transponder chip or smart keys) may need to have their programming done. This requires a computer which is available to the locksmith in the automotive or dealer. Other keys (non transponder keys made of metal), do not need programming. If you need to reprogramme your key, you'll need record the key code number on the tag for the key code.

How do I replace a battery

If the kia sportage smart key key fob is unable to respond when you press the lock/unlock button, it's likely that the battery is insufficient. A battery that is not functioning properly could cause other issues such as the check engine light flashing on or the engine not cranking. Fortunately, replacing the key fob battery is a relatively simple DIY project that requires just some basic tools.

Before beginning the process be sure that your vehicle is turned off and all doors are closed. Locate the small plastic piece that is on the bottom of your key fob and jiggle it until a metal key slides out. This key can be put into the driver door handle to unlock your car.

To replace the key fob battery, remove the rear cover and use a plastic bar tool to release the latch holding the black negative battery cable. Remove the old battery and then orient the new one in a way that the "+" positive side faces your face and the "negative" negative side is facing towards the fob's metal electrical contacts. Avoid using too much force when pushing the new CR2032 into place to avoid damaging or bending the metal contacts.

After the new battery has been installed then turn the key fob off and then turn it on in the ignition several times until the door locks. Then, you can test your 2016 kia forte Key replacement key fob to determine whether it's functioning properly again.

How can you replace the smart key?

You can have an ordinary keyfob or Smart Key, based on the model of Kia Sportage. The smart key is equipped with an embedded mechanical key blade, while the standard keyfob does not. Both types of key fobs are equipped with batteries inside which eventually needs to be replaced. This is a simple procedure that takes only two minutes.

Before you start, you will want to ensure that you are on a flat surface with sufficient lighting and that your Kia is off. Remember that the fob is made up of small parts that can be thrown off if you're not careful.

The small release button is located on the lower backside. This will either be a circular silver button or a rectangular slot. You can open the key fob by pressing the button.

Once you have the key fob open it is easy to take off the old battery and replace it. The new battery should be a CR-2032, and can be purchased online or at your local auto parts store. Once you're done, your key fob should permit you to lock the vehicle, unlock it, and then start your vehicle, even if it isn't running.

How to replace the mechanical key?

The Kia keyfob is a wonderful convenience that lets us lock or unlock our car simply by pressing one button. As with all devices that is used, the Kia key fob may have issues. Luckily, there are steps that can be taken to troubleshoot these issues and ensure that our key fobs are in good condition for the long run.

One of the most frequently encountered issues is a low or dead battery. The fob could be able to cease working or stop working at times. If this is the case, try replacing the battery with a new one.

If this does not resolve the issue, you can use an ordinary screwdriver with a flat head to wedge the fob's casing made of plastic open. Be cautious not to damage any internal components or scratch the plastic. Once the battery is removed and replaced with a new one.

Close and open the door with the mechanical key. (Every kia fob comes with an emergency mechanical key which will fit into the slot). Test the key fob to ensure it's functioning correctly. Contact a dealer, or a locksmith to fix the issue in the event that the fob is not working. Make sure they cut you an emergency key that works across all trunk and door cylinders, to prevent lockouts in the future.