How to Replace a Kia Sportage Replacement Key

The key on many Kia models comes with the keyless entry feature built into. This key usually resembles the remote control and can be replaced with a new one from an kia stinger key Fob dealer or a locksmith.

Key fobs may stop working for a variety of reasons, such as the battery of the coin is dead worn buttons or buttons, signal interference, water damage and a faulty receiver module. Here are some helpful tips to help you get your Kia sportage replacement key working again.

How do you replace the remote key or smartkey?

It doesn't matter if your Kia comes with an intelligent key, remote key, push-to-start key, or regular metal non-transponder key the battery in these keys will eventually need replacing. This is particularly true if your car displays a message telling you that the remote or smart keys aren't powered.

This is a relatively simple procedure. In order to replace the battery in the key fob take out the mechanical key from the slit on the back of the key fob. Next, lift the cover. Inside the key fob will be tiny screws that hold the battery in its place. Remove the old battery by detaching the screw using the help of a small screwdriver. Then, insert the new one and close the slit on the key fob.

Test the key fob by pressing the lock or unlock buttons. You're good to go in case the doors lock and unlock as expected. You can now make use of your Kia's hands-free lock/unlock feature when your fingers are cold or you have to run some errands in Brandon.

Not all key fobs might need to be programmed (transponder chips or smart keys). This requires a programming machine that is available only to the locksmith who works for the automotive dealer. Other keys (non transponder keys made of steel) are not required for programming. If your key has to be programmed again, you will need to know the key code number written on the key code tag and keep it in a safe location.

How do you replace a battery?

If the Kia key fob does not respond to pressing the lock or unlock button, it's likely that the battery is low. A weak battery can cause other issues, such as the check engine light turning on or the engine not cranking. Fortunately, replacing the key fob battery is a simple DIY project that requires only the most basic tools.

Make sure you turn off your vehicle and close all doors prior to beginning. Find the small, metal or plastic piece that is located at the bottom of the key fob. Jiggle it until the key is released. You can then insert the key in the door handle of the driver to unlock your car.

To replace the key fob's battery, remove the rear cover and use a plier bar tool to release the latch that holds the black negative battery cable. Remove the old battery and then orient the replacement battery to ensure that its "+" side faces you, and the "-", negative side is facing the fob's electrical contacts. Avoid using excessive force when pushing the new CR2032 into position to avoid damaging or breaking the metal contacts.

Once the new battery has been installed then turn the key fob off and then on in the ignition for a few times until the door locks cycle. You can then test the Kia's Key fob to ensure it is working correctly.

How to replace a smart key

You could have a standard keyfob or a Smart Key based upon the model of kia rio locked keys in car Sportage. The smart key is equipped with an embedded mechanical key blade, while the standard keyfob does not. Both types of key fobs are equipped with batteries which eventually needs to be replaced. This is an easy process which takes just two minutes.

Before you begin, you will want to ensure that you are on a level surface with adequate lighting and that your Kia is off. Also, remember that there are small parts inside the fob that could fall out if not cautious.

The first step is to find the small release button on the back of the lower part of the fob. It could be a circular button or rectangular slot. You can open the key fob by pressing the button.

After the key fob has been opened, remove the battery that was in it. The new battery should be a CR-2032 and can be bought online or from your local auto parts store. When you're done, the key fob will allow you to lock or unlock and start your vehicle, even if it isn't running.

How do you replace a mechanical key

The Kia keyfob can be a fantastic convenience which allows us to lock or unlock our car simply by pressing the button. But, as with all devices there are issues with it occasionally. Luckily, there are steps to take to troubleshoot these issues and keep our key fobs in good condition for the long term.

One of the most frequently encountered problems is a weak or dead battery. This can cause your device to stop working or work intermittently. If this is the case you should replace the battery with a new one.

If this doesn't solve the issue, try using a standard flathead screwdriver to wedge open the fob's plastic casing. Be cautious not to damage any internal components or scratch the plastic. Once the battery is removed and replaced with a new one.

Close and open the door using the mechanical key. (Every kia fob comes with an emergency mechanical key which will fit into the slot). Test the key fob to verify that it's working correctly. If the key fob isn't functioning, contact a dealer or locksmith to help solve the issue. To avoid a lockout in the future ensure you have an emergency key that will work in all of the trunk and door cylinders.