Reasons Your Fiat 500 Key Fob Won't Work

A key fob with the Fiat bravo key (minecraftcommand.science) 500 number is a great way to open the doors and start the car. However, there are a variety of reasons why the key fob might stop working. These include a dead battery or damaged receiver module, water damage problems, and interference.

This listing is for a NEW replacement Fiat Flip Key Remote - an exact replica of the Ilco brand that must be professionally programmed by a local automotive locksmith (click here for Locksmith Search). Includes lock, unlock, and trunk buttons.

Dead Coin Battery

The most frequent reason that your 500 key fob will not function is a dead battery. Key fobs of today have a limited range of operation and must be within a few inches of your vehicle in order to function. If you are not within your vehicle, and you hit the keyfob, it will not respond, and display the message "Key Fob Not Detected".

If this happens, replace the battery of your coin cell (Part number CR2032) with a fresh one from a reputable brand such as Panasonic, Duracell, or Energizer. You can find them in the local hardware store or online.

After you've changed the battery on the coin cell You can test it by standing next to your Fiat 500 and pressing the buttons. The car should blink its parking lights, and the key fob should operate the lock and unlock buttons.

If the fob's remote doesn't work after replacing the battery, it may be damaged by water, which prevents it from connecting to the receiver module in your car. Water damage can occur in many ways, including an easy splash or submerging your key fob in saltwater at the beach. If you think your fob was exposed to water, you can place it in a bag of rice to draw out the moisture. If this doesn't work, the fob might require reprogramming by a professional auto locksmith or the dealer.

Water Damage

Water damage can occur if you immerse the fob in the ocean, or wash it in a washing machine. Saltwater is especially dangerous to the circuit board of the fob, causing it to short out and eventually die. It's not a good thing to let the fob get wet however, don't give it up in the event that you accidentally drop it in water or forget to take it out of your pants pocket.

First, remove the battery. Before replacing the battery clean the electronic chip using isopropyl, or a similar product. Test the fob afterward to verify if it's functioning. If the key does not work, it may have to be changed. This is usually handled by a professional or dealer auto locksmith.

If the key you have is older and not programmed to work with your vehicle, you will need to replace it completely. This is a simple procedure which can be accomplished by a professional locksmith for automotive use. The locksmith will have to cut the key to match the ignition on your vehicle. They will also need to reprogram the fob for your vehicle's system. This is a simple and cost-effective process that can usually be completed on the same day.

Receiver Module Issues

One of the main reasons why your 500 key fob may stop working is that it's simply out of range. The remote typically has an operating range of 30 feet or less and if it's far from your car, it won't respond to your commands. This can be easily fixed by moving it closer to your vehicle until it begins responding.

If your fob won't work after replacing the battery inside the coin, which is also called a "button", "watch" or "button" or "button", it could be due to a problem with the internal circuit board. In most cases, reprogramming the fob will solve the problem. You can find the instructions for the majority of vehicles on YouTube or in the owner's guide.

It is possible to replace the clips made of metal that hold the coin batteries in the correct position. If they lose tension it could prevent your coin battery from being properly seated, causing your remote to malfunction.

In rare cases, the fob may become desync'd with your vehicle because of software or hardware issues. It is possible to fix this issue by visiting your local auto-locksmith or dealer to reprogram your key fob. In some instances it may be necessary to install the software again in your body control module, as well.

Interference

In addition to a dead battery on a coin The key fob may not be able to transmit or receive signals due to interference. This is possible when the key fob is located near radio transmitters (cell phones, radar detectors) or another source of electromagnetic radiation. Other reasons why the key for fiat 500 fob might not work include a poor connection to the buttons or the internal chip or water damage.

If your key fob suddenly stopped working, or you have tried everything at home to solve the issue (e.g. replacing batteries, reprogramming or using the spare key fob, it could have a damaged receiver module on your 500. The receiver module, located under the dashboard, is able to pick up radio frequency signals from your key fob. It converts the signals into electronic commands that are then processed by the vehicle.

There's a simple method to reset the 500's onboard system, including the keyfob. Disconnect the battery 12 volt for about 15 minutes, by taking off the negative cable first then the positive cable. Reconnect the battery. This will remove any residual electricity and restart the car's computers, which could allow you to get your key fob working again. If the issue continues, you should speak with an expert technician. They will be able to determine the root of any problems.