Peugeot 208 Key Replacement

Peugeot 208 key replacement should be left to experienced auto locksmiths who have the proper equipment and technical knowledge. They can create and program keys quicker and more efficiently than dealerships.

If the key fob has stopped locking or unlocking your doors it could be due to a dead coin battery. There are also other reasons that the key might be malfunctioning.

Dead Coin Battery

A dead coin battery can prevent your peugeot car key (gokseong.multiiq.com) 208 from locking or unlocking, and won't start the engine. In this scenario you'll have to choose the alternate method to start that is described in the owner's manual.

The spark plugs might also be worn out. The spark plugs are responsible to ignite the fuel that powers the engine. However they are limited in their lifespan. If they are not used enough and they fail, they'll eventually die.

There is a straightforward solution to this issue. The best option is to measure the voltage of your car battery using a multimeter. If the voltage is below 11,5 volts then it's time to replace it. If the battery is damaged, it is important to clean its contacts. This can be done by removing the rubber cover from the two terminals of the battery, and then using a wirebrush, you can remove any damaged parts of the battery. Then, reconnect the positive pole cables to the negative.

Water Damage

If your 208 won't start and the battery hasn't failed, you should examine the spark plugs. It could be that they are simply too dirty and don't spark. The spark plugs can be cleaned in an workshop.

Peugeot cars have keys that are transponder-type and works with the car's immobiliser system. This ensures that only the correct key is able to start the engine. If the chip inside the Peugeot key is damaged, it won't transmit the correct signal to the vehicle.

Water damage is a common cause of this problem. This is a typical issue in warmer climates where the vehicle has been exposed to snow or rain. In this instance, you should contact a reliable locksmith who has the required tools and equipment to change the key's programming. They will also have the latest technology and equipment needed to make a Peugeot smart key. The process should take no more than 15 minutes.

Contacts of the battery may be damaged.

Peugeot replaced the old transponder chips by introducing a new version that makes use of electronic components that are mounted on a circuitboard. The new system is fantastic when it's new, however the circuit boards degrade over time and cease to function properly.

This can prevent the immobiliser chip from triggering, so your car won't start. If this happens it's best to get in touch with a Peugeot specialist or locksmith.

The most frequent issue is when the battery inside the key fob starts to fail. This causes the blade of the key to stop feeding into the lock. A car locksmith will replace the battery, and then cut a new blade for you. This is a simple solution.

Faulty Receiver Module

It could be that the receiver module is defective in the event that your Peugeot key fob stops working after being dropped on the floor, or exposed to a stormy rainstorm, or accidentally washed. The receiver is responsible for sending radio frequency signals to the on-board computer, which controls the central locking system of your Peugeot vehicle.

The key fob itself is fitted with rubber seals to prevent water from reaching the electronic chip inside. The chip can be damaged by water when exposed to water for a long time. Submerging the key fob in ocean water on the beach or throwing it into the water can be especially damaging because of the high salt content.

If your Peugeot spare key fob stops working then you'll have to get the module replaced. This is only done by a skilled auto locksmith or Peugeot specialist. Peugeot keys are, unlike other vehicles, are secured by an immobilizer device. This requires the right codes to start the car. This is why you should only be able to trust a professional Peugeot locksmith with the task of designing and programming an appropriate replacement.

Computer on-board is not working properly

The computer on board in your Peugeot is the one responsible for all of the systems in the car, from power windows to airbags. The computer on board will display a code if something goes wrong. This code will be stored within the system until the problem is fixed. Most often, this involves replacing the computer on board.

The most frequent cause for the warning light for airbags to flash is corrosion or loose connections in the sensor. This can be caused by wear and tear, aging, exposure to moisture and salt. It is essential to have this issue addressed as quickly as possible, since an airbag that is not functioning properly could be dangerous in the event an accident.

If you encounter the error "card not found" on your Peugeot key fob, the battery in the key fob may be dead or weak. This will stop the key fob sending a signal to disable the immobilizer on your vehicle. You can test this by pressing the unlock button on the key fob, then attempting to start your car. If it doesn't work the battery on the key must be replaced.