How to Replace a Kia Sportage Replacement Key

For many Kia models, the key contains the keyless entry system that is built into the key. This key is similar to remote controls, and can be exchanged by a Kia dealer.

Key fobs may stop working for a variety of reasons, such as the battery of the coin is dead, worn buttons or buttons, signal interference, water damage, and a defective receiver module. Here are some helpful tips on how to get your Kia Sportage replacement key to function again.

How to replace the remote key or smart key?

It doesn't matter if your Kia comes with an intelligent key, remote key push-to-start keys, or a standard non-transponder key made of metal the battery in these keys will eventually require replacement. This is especially relevant if your car displays a message telling that the smart key or remote has low battery power.

Fortunately, it's quite simple to do. To replace the battery of the keyfob, remove your mechanical key from the slit on the back of the fob. Then, push the cover off. Inside the key fob, there will be an incredibly small screw that holds the battery in place. Remove the old battery by unscrewing the screw with the help of a small screwdriver. Then, insert the new and close the hole in the key fob.

When the key fob is equipped with new batteries check it by pressing the locks and unlock buttons. It's okay if the doors lock and unlock as you expect. You can now utilize Kia's hands-free lock/unlock function whenever your fingers get chilly or you have to make errands in Brandon.

Note: Certain key fobs might need to be programmed (transponder chips or smart keys). This requires a particular programming machine that only the dealer or locksmith can access. Other keys (non-transponder metal keys) do not require programming. If your key has to be programmed again, you must be aware of the number that is stamped on the tag that identifies the key and save it in a secure location.

How do I replace the battery?

If the Kia key fob is unable to respond to pressing the lock or unlock button, it is likely that the battery is depleted. A low battery may cause other issues, such as the check engine light flashing or the engine not working properly. Fortunately replacing the key fob battery is a simple DIY task that requires only the most basic tools.

Make sure you turn off your vehicle and shut the doors before you begin. Find the small metal or a plastic piece on the bottom of the key fob. Jiggle it until the metal key comes out. This key can be placed inside the driver door handle to unlock your car.

To replace the battery on the key fob, you must remove the rear cover. Utilize a plastic plier tool to loosen up the latch that holds the black negative cable. Remove the old battery and orient the new one in a way that the "+" positive side is facing you, and the "-" negative side is facing towards the fob's electrical contacts made of metal. Push the new CR2032 battery straight into position and avoid excessive force to avoid damaging or bending the metal contacts.

Once the new battery is installed and the key fob is turned on, turn it off and on in the ignition until the door locks. Then you can test your kia key fob replacement key fob to determine whether it's working again.

How to replace the smart key?

There is a possibility of having a standard keyfob or a Smart Key depending on the model of Kia Sportage. The smart key features an embedded mechanical key blade, while the standard keyfob does not. Both key fobs come with an internal battery that will eventually require replacing. It's an easy task that will take about two minutes.

Be sure to turn off your Kia, and be on a flat well-lit and well-lit area before you begin. Remember that the fob is made up of tiny parts that could be thrown off if you're not careful.

The first step is to locate the small release button that is located on the backside of the fob. It will be an oval or circular slot. After pressing this button, the mechanical key blade will pop out and you can then open the key fob.

Once you have the key fob open it is easy to take out the old battery and replace it. The new battery is a CR-2032, and can be bought on the internet or at your local auto parts store. When you're done, the key fob will allow you to lock the vehicle, unlock it, and then start your vehicle, even if it isn't running.

How to replace a mechanical key

The Kia key fob is a fantastic option that lets us lock and unlock our car at the press of one button. Like any other device it will encounter issues occasionally. There are ways to fix these issues and ensure that our key fobs are in good working condition over the long haul.

One of the most common problems is a low or dead battery. This can cause your device to stop working or work intermittently. If this is the case try replacing the battery with a fresh new one.

If this isn't enough to solve the issue, try using a flathead screwdriver standard to push the fob's casing made of plastic open. Be careful not to scratch any internal components or scratch the plastic. Once the battery is opened, carefully remove the battery you have been using and replace it with a brand new one.

When the new battery is in, close and then open the doors using the mechanical key (every kia ceed key fob fob comes with an emergency mechanical key that can fit in the slot). Test the key fob to confirm it's working as intended. If the device isn't working, call an expert locksmith or dealer to resolve the problem. Make sure they cut you an emergency key that functions across all trunk and door cylinders, to prevent lockouts in the future.