How to Replace a Kia Sportage Replacement Key

The key of a lot of Kia models comes with an entry system that is keyless in. The key functions like a remote control and can be exchanged with an Kia dealer.

Key fobs may stop working due to various reasons, such as batteries that are dead worn buttons signal interference, water damage and a malfunctioning receiver module. Here are some helpful tips to assist you in getting your Kia sportage replacement key working once more.

How do you replace the remote key or the smart key?

The battery inside your Kia's smart key will eventually need be replaced, regardless of whether it's a remote, a push-to-start key or a standard metal key that doesn't have transponder. This is particularly relevant if your vehicle shows a message that states the smart or remote keys have low battery power.

It's a simple procedure. In order to replace the key fob battery, remove the mechanical key from the hole in the back of the key fob and lift the cover. A small screw will be found inside the key fob to hold the battery in place. By using a small screwdriver unscrew the screw and remove the old battery. Then, insert the new and close the hole in the key fob.

Once the key fob has new batteries and you've tested it, press the locks and unlock buttons. If the doors unlock and lock exactly as you expect, then you're set! You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers start to get chilly or when you need to go on errands around Brandon.

Note: Some keys may require to be programmed (transponder chips or smart keys). This requires a machine for programming that is available only to the locksmith who works for the automotive dealer. Other keys (non transponder keys made of metal) are not required for programming a kia key fob. If you need to reprogramme your key, you'll need to write down the key code's number on the key code tag.

How do you replace the battery?

If the Kia key fob doesn't respond to pressing the lock/unlock button, it is most likely that the battery is not fully charged. A low battery may also cause other issues like the check engine light turning on or delayed engine cranking. It is easy to replace the key fob batteries by using only the use of a few tools.

Be sure to turn off your vehicle and shut all doors prior to beginning. Locate the small plastic piece at the bottom of your key fob, and jiggle it until a metal key slips out. Then, you can insert the key into the handle of the door for the driver to unlock your car.

To replace the key fob battery, remove the cover at the rear and use a plastic pry bar tool to release the latch that holds the black negative battery cable. Remove the old battery, and then align the new battery in a way that the "+" positive side is facing your face and the "negative" negative side is facing the fob's electronic contacts. Push the new CR2032 battery straight into position with care to avoid using too much force to avoid bending or damaging the contacts on the metal.

After installing the new battery then turn the key fob on and off in the ignition until the door locks up. Then, test your Kia key fob to determine if it is working properly again.

How to replace the smart key?

You may have either a standard keyfob or a Smart Key based on the model of Kia Sportage. The smart key has an embedded mechanical key blade however, the standard key fob does not. Both key fobs contain a battery that will eventually need to be changed. Fortunately, it's an easy task that takes only two minutes.

Be sure to switch off your Kia Key Car and sit on a flat well-lit and well-lit area before you begin. Also, keep in mind that there are small parts inside the fob that could fall out if not cautious.

The first step is to find the small release button on the lower backside of the fob. It can be an oval silver button or a rectangular slot. After pressing this button mechanical key blade, it will pop out and you will be able to open the key fob.

After the key fob has been opened, remove the battery. The new battery is a CR-2032, and can be purchased from a local or online auto parts shop. When you are done it should be possible to lock or unlock your car with your key fob even if your engine isn't running!

How to replace a mechanical key

The Kia key fob is a fantastic convenience that lets us lock and unlock our car at the push of a button. But, as with all devices, it can have problems occasionally. There are ways to resolve these issues and keep your key fobs running for a long time.

A dead or low-quality battery is one of the most common problems. This can cause your device to stop working or operate intermittently. If this is the case you should replace the battery with a fresh new one.

If this doesn't resolve the problem you can try using a standard flat-head screwdriver to break open the casing of the fob's plastic. Be cautious not to damage any internal components or scratch the plastic. After opening, carefully remove the battery that was removed and replace it with a brand new one.

Close and open the door with the mechanical key. (Every Kia fob comes with an emergency mechanical key which will fit into the slot). Test the key fob and make sure it is working properly. Contact a dealer or a locksmith to resolve the problem when the fob still is not working. To avoid future lockouts, make sure you get an emergency key that can be able to work with all door and trunk cylinders.