How to Replace a kia picanto spare key (Visit Home Page) Sportage Replacement Key

The key on many Kia models has a keyless entry system built in. The key functions like remote controls and can be exchanged by an Kia dealer.

Key fobs might stop working for several reasons, including a dead coin battery worn buttons, signal interference, water damage and a malfunctioning receiver module. Here are some tips to assist you in getting your Kia sportage replacement key to work for good.

How do you replace a remote key or smartkey

The battery in your Kia's intelligent key will eventually need be replaced, regardless of whether it is a remote key, a push-to-start key or a regular metal key that is not equipped with an electronic transponder. This is especially when your car shows a message that states the smart or remote keys are not powered by batteries.

Fortunately, it's a relatively simple process. In order to replace the battery in the key fob, remove the mechanical key from the slit on the back of the key fob. Next, break the cover. Inside the key fob there will be a small screw that holds the battery in its place. With a small screwdriver, unscrew the screw and pull out the battery that was in place. Insert the new battery and close the slit on the key fob.

Once the key fob has new batteries and you've tested it, press the lock and unlock buttons. If the doors lock and unlock in the same way, you're set! You can now make use of Kia's hands-free lock/unlock function when your fingers start to get cold or you need to make errands in Brandon.

Note: Some key fobs (transponder chip or smart keys) may require their programming done. This requires a computer that is available only to the locksmith for cars or dealer. Other keys (non transponder keys made of steel) do not require programming. If your key needs to be programmed, you must be aware of the number written on the key code tag and keep it in a safe place.

How do you replace a battery?

If your kia key replacement key fob is not responding to pressing the lock or unlock button on the fob, it is a sign that the battery needs to be replaced. A weak battery can cause other issues like the check engine light turning on or the engine not cranking. Fortunately, replacing the battery on the key fob is a relatively simple DIY project that requires just a few basic tools.

Before you begin ensure that your vehicle is turned off and that all doors are shut. Find the small metal or a plastic piece near the bottom of the key fob. Jiggle it until the metal key is released. The key can be placed inside the driver door handle to unlock your car.

To replace the battery in the key fob, you must remove the cover on the rear. Make use of a plastic pry tool to remove the latch that holds the black negative cable. Remove the old battery, and then align the replacement battery in a way that its "+" side faces you and the "-", negative side is facing the fob's electrical contacts. Avoid using excessive force when pushing the new CR2032 into place to avoid damage or bending the metal contacts.

Once the new battery is installed after which you turn the key fob off and on in the ignition for a few times until the door locks cycle. You can then test your Kia's key fob once more to ensure it's working properly.

How do you replace a smart keys

You can have the standard keyfob or Smart Key based on the model of Kia Sportage. The difference is that the smart key has an incredibly small key blade tucked inside it, while the standard fob does not. Both types of key fobs have batteries inside that will eventually have to be replaced. Fortunately, this is an easy task that takes just two minutes.

Be sure to turn off your Kia and sit on a flat well-lit and well-lit area before you begin. Also, remember that there are tiny components inside the fob that can be snagged if not cautious.

The first step is to find the small release button on the lower backside of the fob. It could be a circular button or a rectangular slot. You can open the key fob by pressing the button.

Once you have the key fob open and you are able to remove the old battery and replace it. The new battery is one called CR-2032 and can be purchased on the internet or at your local auto parts shop. After you're done, your key fob should permit you to lock and unlock your vehicle even if it's not running.

How do I replace the mechanical key

The Kia keyfob can be a fantastic convenience that allows us to lock or unlock our car simply by pressing one button. But like any device it will encounter issues at times. There are ways to troubleshoot these issues and keep our key fobs in good condition over the long haul.

A dead or low-quality battery is one of the most common issues. This can cause your fob to stop working or operate intermittently. If this is the case, replace the battery with a new one.

If this isn't enough to resolve the issue Try using a standard flat-head screwdriver to break open the casing of the fob's plastic. Be careful not to damage any internal components or scratch the plastic. After opening, carefully remove the battery you have been using and replace it with a new one.

Close and open the door using the mechanical key. (Every kia fob comes with an emergency mechanical key that fits into the slot). Test the key fob to confirm it's functioning properly. Contact a dealer, or a locksmith to solve the issue if the fob is still not working. To avoid a lockout in the future ensure that you have an emergency key that will work on all trunk and door cylinders.