How to Replace a Kia Sportage Replacement Key

For a number of Kia models the key comes with a built-in keyless entry system. This key usually resembles an remote control, and can be exchanged with a brand new one from a 2013 kia rio Key Replacement dealer or a locksmith.

Key fobs can stop working due to a variety of reasons, such as the battery being dead, worn-out buttons signal interference or water damage. Here are some suggestions to assist you in getting your Kia sportage replacement key to work for good.

How to replace a remote key or a smartkey?

No matter if your kia optima keys comes with an intelligent key, remote key push to start key, or a regular non-transponder steel key the battery in these keys will eventually require replacement. This is especially relevant if your vehicle displays a message indicating that the remote or smart keys aren't powered.

Fortunately, it's quite simple to do. To replace the key fob battery take out the mechanical key from the slit in the back of the key fob. Next, pry open the cover. A small screw is inside the key fob that holds the battery in its place. Using a small screwdriver, loosen the screw and pull out the battery that was in place. Insert the new battery and then close the opening on the key fob.

When the key fob is equipped with an updated battery, test it by pressing the locks and unlock buttons. It's okay in case the doors lock and unlock as expected. You can now take advantage of the hands-free lock/unlock feature on your Kia when your fingers are cold or you need to make errands in Brandon.

Note: Some key fobs could need to be programmed (transponder chips or smart keys). This requires a computer, which is only available to the locksmith who works for the automotive dealer. Other keys (non transponder keys made of metal) are not required for programming. If you're looking to reprogramme your key, it is necessary to record the key code number on the key code tag.

How do you replace a dead battery?

If the Kia key fob does not respond to pressing the lock or unlock button, it is likely that the battery is not fully charged. A weak battery could cause other issues, like the check engine light flashing or the engine not turning properly. Fortunately, replacing the key fob battery is a relatively easy DIY project that requires just a few basic tools.

Before you begin before beginning the process, ensure that your vehicle is off and all doors are shut. Find the small metal or plastic piece near the bottom of the key fob. Move it until the metal key pops out. You can then put the key into the handle on the door of your driver to unlock your car.

To replace the key fob's battery, remove the cover at the rear and use a plastic pry bar tool to loosen the latch that holds the black negative battery cable. Remove the old battery, and then align the replacement battery in a way that its "+" side is facing you, and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position with care to avoid using too much force to avoid damaging or bending the contacts on the metal.

Once the new battery has been installed after which you turn the key fob off and then on in the ignition for a few times until the door locks. You can then test your Kia key fob and see whether it's functioning properly again.

How to replace the smart key

Depending on the model of the Kia Sportage, you may have the standard key fob, or a smart key. The smart key comes with an embedded mechanical key blade, while the standard key fob does not. Both key fobs come with batteries that eventually need to be changed. Fortunately, this is an easy process that only takes about two minutes.

Before you get started it is essential to ensure that you're on a level surface with sufficient lighting and that your Kia is turned off. Be aware that the fob is made up of small parts that can be thrown off should you not be careful.

The first step is to locate the small release button on the backside of the fob. It's either an oval or circular slot. You can open the key fob by pressing the button.

Once the key fob is opened, remove the battery. The new battery is a CR-2032 that can be purchased online or at a local auto parts store. After you're done, your key fob should permit you to lock and unlock your vehicle, even if it isn't running.

How do you replace the mechanical key?

The Kia key fob is an amazing feature that lets us lock and unlock our vehicle with the press of the button. Like any other device it will encounter issues occasionally. There are steps that can be taken to solve these issues and ensure that our key fobs are in good condition in the long run.

A dead or drained battery is one of the most common issues. This could cause the fob to stop working completely or stop working at times. If this happens, try replacing the battery with a fresh new one.

If this doesn't solve the issue, use an ordinary screwdriver with a flat head to wedge the plastic casing of the fob open. Be careful not to harm any internal components or scratch the plastic. Once the battery is removed and replaced with a new one.

Close and open the door with the mechanical key. (Every kia fob comes with a spare mechanical key which will fit into the slot). Test the key fob and check that it's functioning correctly. Contact a dealer or a locksmith to solve the issue in the event that the key fob is not working. Make sure they cut you an emergency key that can work across all door and trunk cylinders to avoid lockouts again.