Fiat 500 Replacement Key Fob

It might be time to replace the battery if the 500 remote key fob isn't working. If you replace the battery, but it still doesn't work it could be a problem elsewhere.

United Locksmith specializes in the production of new keys for classic vehicles. We have all the tools and accessories needed for this service.

Dead Coin Battery

A dead battery is the most frequent reason for your Fiat 500 keyfob not locking or unlocking the doors. The key fob contains the battery of a coin-cell that can quickly deplete when it isn't frequented enough. If your remote has started to show signs of a loss of range, or has stopped functioning and the battery is not working, it could be dead.

The battery inside the key fob is secured by metal clips that retain it. If the clips are not tight, they can cause problems with contact that can prevent your remote to receive power. Use a flathead screwdriver remove the retaining clip and remove the battery. Make sure you use a replacement with the same kind of voltage, size, and specification as the original battery.

Water exposure can also cause the key fob to corrode, or even become damaged. Even a small shower in soapy water can damage the electronic chip inside. Make sure your key fob is dry.

Water Damage

If your key fob isn't working correctly, it could be due to water damage. Key fobs come with rubber seals that stop them from being damaged by light rain or a splash of water, but it is vital to keep your car keys away from the ocean, pool, and the washing machine!

The key fob comes with an electronic chip that sends a message to the immobilizer system of your car. This is what allows your 500 to lock or start, but if the chip gets saturated, it won't be able to longer work.

You can try cleaning the inside of your key fob's electronics using isopropyl alcohol, or an electronic cleaner to see if they are still good. However, it is probably better to purchase a replacement key for fiat 500 from a dealer instead of trying to repair the key fob that is submerged in salt water.

A replacement fiat 500 key fob fob can cost you a little bit but it's far less expensive than paying to have your Fiat 500 towed to a dealer and fixed there! Plus, you can do it yourself in a few easy steps. Be sure to have the correct type of battery before you attempt to open your keyfob. This is a job that's much simpler than it appears and there are step-by-step instructions on the internet for nearly any car key fob.

Faulty Chip

The chip inside the key fob communicates with the immobiliser on your vehicle to ensure that the vehicle will start only when the correct keys are used. If the chip is damaged or destroyed, your car won't start regardless of what you do.

A chip that is defective can happen due to a variety of reasons but the most common reason is water damage or a dead battery. It is recommended to leave the job to a professional locksmith who can repair the chip in a short time and at a reasonable cost.

If your key fob does not work after exposure to clean tap or rain water then remove the battery. Wipe down the electronic component using paper towels. If the key fob still fails to work it's probably to be a damaged chip that is required to be replaced.

Some people go to their dealer when they require a new Fiat fob. However, this could be costly. If you are seeking a cost-effective method to have your Fiat key fob repaired then look no further than United Locksmith. We have all the tools and experience needed to repair your Fiat fob in a timely and professional manner.

Faulty Receiver Module

Fiat key fobs send a signal to the vehicle, which will unlock and close doors (and start the vehicle for those with an automatic transmission) up to 50 feet. However, there are some things that can cause the fob to cease functioning. This could be due to a dead coin battery water damage buttons, worn out buttons, a receiver module issue, and signal interference or a malfunctioning electronic chip.

If the fob was placed in a pocket that experienced extreme trauma, like being dropped on hard floor or getting washed in the washing machine, it may not be able to communicate with the car's Body Control Module (BCM). This is because the BCM is an extremely secure system that will only accept signals from a genuine key, and not from any other.

If this is the case, then you will need to replace your fob. A professional locksmith can handle all aspects of the key replacement process and even program a new one for your 500. They can even offer a clone fob that works exactly like the original (and costs a fraction of what it would cost).