Double Glazing Door Lock Repairs

Has your uPVC window or door mechanism become faulty? Perhaps the handles on your uPVC windows and doors are not aligned properly or are difficult to operate.

It is essential that your double-glazed doors work smoothly, otherwise you will lose energy and increase the chances of burglary. Owen the Locksmith will be able to repair your door lock for reasonable costs.

Snapped Key

It can be quite frustrating when a key gets stuck inside a lock. It also poses a security risk, as the door might not lock and make you vulnerable to intruders. Fortunately, there are simple fixes you can use to solve the problem and get your door working properly once more.

Be calm. If you panic you could end up pushing the broken key further into the lock.

Spray WD-40, or any other penetrating lubricant, into the lock. This will help the broken piece to be removed more easily. You can also use a screwdriver to help break up any pieces stuck that might be blocking the way. If you have a part of the key that's still sticking out, grab it with a paperclip or other thin metal object and pull it. Both methods are effective, but you need to be careful not to push the damaged key further into the keyway.

Some paperclips have grooved edges that can be used as hook extractors. Jigsaw blades can also work well for this. If you don't happen to have any of these items you can bend a hook using needle-nosed pliers. Additionally, a pair of tweezers can be used to grasp and pull out the remaining bit of the broken key.

If you're unable to pull the broken piece of the key out, try using a lock de-icer. It's available at most hardware stores and is used to freeze any moisture present inside the lock.

If none of these tricks seem to be helping you, it's time to call in locksmith. The experts at Fitlocks can quickly fix problems such as broken handles and broken keys with uPVC locks and door mechanisms. They can also reconfigure your double glazing door mechanisms to make them more user-friendly. You can schedule repairs to your double-glazing online or call us to discuss your requirements.

Broken Cylinder

A broken cylinder can pose a major security risk. It's a good thing that it's a simple repair for an expert locksmith to complete. A locksmith must tap the cylinder to repair it. They can do this using a hammer or other tool, but the most efficient method is to make use of a long match or piece of wire. Then, position the end of the match or wire close to the keyway. The locksmith will then strike the lock in order to break it. This is far better than using a heavy hammer, which could harm the lock.

The most frequent cause of cracks in the cylinder head is overheating. This can occur when the block and the cylinder head are made of different metals like cast-iron and aluminium. When various metals are heated and cool at different rates, it may create hotspots in the local area that expand faster than the rest of the cylinder head, leading to cracks.

Corrosion is a different cause of cracks in the cylinder. If the head and block of the cylinder are not maintained in a timely manner they may be corroded or rust, which can cause them to expand faster than anticipated. This can cause cracks over time.

If your uPVC window repairs near me or door lock is stiff and requires a lot more pressure to turn it could be due to a variety of causes. This issue could result from a defective locking mechanism or misalignment as well as a worn-out handle.

Fortunately, this is an easy and affordable fix for the majority of homeowners of double glazing. A professional locksmith should be able to resolve the issue within an hour of arriving at your property. Based on your requirements they will be able to replace the locking mechanism, change the window handles, and also change the gearboxes. A skilled locksmith will always be able to advise you of the most cost-effective option for your home. They can even recommend upgrades to the highest-security 3 Star TS007 euro cylinders that will add an extra layer of protection against burglars. This is a small cost to pay for the security that comes from knowing your upvc door repairs Near Me doors are secure.

Broken Handle

It's not surprising that window handle locks may break. They have intricate mechanisms that become less effective over time. It can be difficult to determine the reason for the broken window handle lock and fix it correctly.

Fixing the broken handle, regardless of whether it's the internal locking mechanism or latch will increase the security of your uPVC door and reduce the risk of draughts. It can be expensive to replace or repair your handle if it is not done correctly and can also harm the frame and the lock of your door.

With the window open and the window open, loosen the screw that holds the handle by using the screwdriver. The screw should be on the inside of the back plate, normally concealed by a screw cover for aesthetic reasons. Be sure not to lose any internal components within the handle, such as the levers or plates on the opposite side of the spindle. Ideally, keep them in the same place so you can replace them again if needed.

Next, turn the handle until it's 90 degrees to the window frame. Finally, loosen the screw at the back of the handle which holds it to the internal spindle using another screwdriver. Once the screw is loose, pull the handle out and take the broken spindle out. Replace it with a new spindle, ensuring that it's the same length (you can find them online or in hardware stores). Screw it in the correct position. Be cautious not to overtighten as this could cause damage to the handle or the window frame.

Close the handle and test it. It should work smoothly and you'll be able to open your window after a few times.

While you're working on the handle, make sure to make sure your uPVC windows are closing properly. If they're not closing properly, you could experience draughts and damp in your home as and also affecting the efficiency of your home's energy usage. A local window company, such as Core Sash Windows, will be capable of adjusting the hinges on your window frames to ensure they shut correctly.

Broken Spindle

It is quite common that the spindle within the handle breaks, rather than the handle itself. This is especially frequent in uPVC tilt and turn windows. These windows require a handle that acts as an locking device within the window frame. The handle is attached to a central rod that triggers the mushroom-shaped locking cams that secure the window frame keep. If the dead latch mechanism does not open when the handle is turned it is possible that the spindle has broken, this can be a very frustrating issue.

There are ways to fix this issue. A good locksmith will be able to quickly and effectively fix this issue. A professional locksmith will be able disassemble the window's handle using a tool that removes the wheel part in which the spindle is. This is done without causing any damage to the handle or causing any other damage to the window frame.

After removing the wheel, the technician can examine the spindle to determine the cause of the break. This involves breaking the spindle into its component parts and meticulously noting their general condition, as in addition to any specific areas of damage or excessive wear. This procedure is usually performed in a clean environment by highly skilled technicians.

The next step is to clean the damaged spindle. This will help get rid of any dirt or debris which might be preventing it from operating normally. The spindle can then be repaired or replaced. If the technician is replacing the spindle the dowel can be used that is similar in size to the original. Then, he will make holes in the same way into both pieces. This will ensure that the spindle will fit perfectly with the handle.

If the damaged spindle cannot be repaired, it could require replacement completely. Home centres sell generic replacements, but if the design of your window is rare then it will be necessary to speak with a woodworker or cabinet maker who can replicate the exact component for you. Once the spindle has been installed, it is fixed to the handle. Line up the screw holes on the handle to the screws already in the frame. Once the handle is set, you are able to operate your uPVC windows.