Reasons Your fiat 500 electric key 500 Key Fob Won't Work

A key fob from fiat Panda key fob replacement 500 is a handy way to open the doors and start the car. There are a myriad of reasons the fob won't work. This includes a dead battery water damage, problems with the receiver modules, and interference.

This listing is for a NEW replacement fiat key replacement cost Flip Key Remote that looks like the Ilco brand. It needs to be professionally programmed (click here to search for local locksmiths for automotive locksmiths). It includes lock, unlock, and trunk buttons.

Dead Coin Battery

A dead battery is the most frequent reason for your 500 key fob being inoperative. Modern key fobs come with a limited range of operation, and must be within just a few feet of the vehicle to function. If you're far from your vehicle and you press the key fob button the car will not respond, and will display the "fiat 500x key fob Fob Not Detected" message in the instrument cluster.

If this occurs If this happens, replace the battery in the coin-cell (Part Number CR2032) by a fresh one of a reputable brand such as Panasonic Duracell or Energizer. They are usually available in your local hardware store or online.

You can test the battery on your coin-cell by pressing the buttons while you're standing close to your fiat punto replacement key 500. The car should flash its parking lights, and the key fob should be able to operate the lock and unlock switches.

If your key fob does not work after replacing the battery, it might be water damage that is preventing it from interacting with the module in your vehicle. Water damage can happen through a variety of methods, including the simple splash or submerging the key fob in saltwater at the beach. If you suspect that your fob has been exposed to water, try placing it in a dry rice bag to draw the moisture back out. If this doesn't work, you will need to have your fob changed by an auto locksmith or a dealer.

Water Damage

Water damage can happen if you immerse the fob into the ocean or wash it in a machine. Saltwater can be particularly harmful to the circuit board of the fob that can cause it to short out and eventually end up dying. In the event that you let your fob get wet, it's not an option but if you accidentally drop it into an empty cup of water, or don't remember to remove it from your pants pocket prior to running the washer do not give up hope.

First, remove the battery. Before replacing the battery, clean the electronic chip with isopropyl, or a similar product. Next, test the fob to check if it functions. If the key isn't working it could need to be programmed again. This is usually handled by a professional or dealer auto locksmith.

If the key is more recent and has not been programmed to your vehicle, it will likely need to be replaced completely. A professional automotive locksmith can complete this simple process. The locksmith will need to cut the key to match the ignition of your car. The locksmith also needs to reprogram your fob in the car's system. This is a low-cost and fast process that can be completed the same day.

Receiver Module Issues

Your 500 key fob might not function because it's out of range. The remote has a range of 30 feet, so in the event that you are far from your vehicle, it won't respond to your commands. This can easily be resolved by moving closer to your vehicle until it starts responding.

If you've replaced your coin battery (commonly called"button" or "button" or "watch") and the fob won't work, it could have an internal circuit board problem. In most cases, reprogramming the fob can resolve the problem. You can find the instructions on how to do this for all vehicles by searching YouTube or checking out the owner's manual.

It is possible to replace the metal retaining clips that hold the coin battery in place. If they lose tension it can prevent the battery from being properly seated and can result in the malfunction of your remote.

In rare cases, the fob may become disconnected from your vehicle because of software or hardware issues. You can fix this problem by visiting your local auto-locksmith or dealer to reprogram your key fob. In certain situations it may be necessary to install the software again in your body control module as well.

Interference

In addition to a dead battery on a coin, the key fob may not be able to receive or transmit a signal due to interference. This can happen when the key fob is near a radio transmitter (cell phones, radar detectors) or another source of electromagnetic radiation. The key fob could not work because of a problem to the buttons or water damage, or damage to the internal chips.

If the key fob has stopped working one day in the middle of the night, or after trying everything you can at home to solve it e.g. battery replacement, reprogramming and using the spare key fob, it could have a malfunctioning receiver module on your 500. The receiver module, located beneath the dashboard, detects radio frequency signals from your key fob. It then converts them into electronic commands that the vehicle interprets.

Fortunately, there's an easy way to reset all on-board systems in your 500 keys, including the key fob. Disconnect the 12 volt battery for about 15 minutes, by removing the negative cable and then the positive cable. Then reconnect the battery. This will clear any residual electrical charge, and then restart the car's computer. This could help you get your key fob to function again. If the issue persists, you should consult an expert technician. They can identify the exact cause of problems.