Replacement UPVC Door Handles

You can find the ideal handle for your door, whether replacing your handles or adding extra security. These window handles made of upvc are easy to install and have the required 92mm center distance of multipoint locks.

The backplate's fixing centre as well as the keyhole/lever dimensions are the most important measurements. Compare these measurements carefully with your existing marks before ordering.

Lever/Pad

Lever pad handles for doors consist of an elongated lever handle on one side and a paddle shaped handle on the other. They are designed to be used with key wind locks. However they can also be attached to multipoint split spindle door locks.

Our range of upvc handle lever pads are available in a range of finishes. These will be listed in the drop-down list after you have selected the right handle for your doors. Not all styles of handles are available in every finish though and you should always check the sizes and technical drawings for the specific product that you're looking for to ensure that you get the right size and fit.

When you are choosing a new set of lever pad door handles made of Upvc it is crucial to make sure that they correspond to the PZ (distance between the spindle of the handle and the centre of the hole for the cylinder) of your existing multipoint locks, as these need to be in the same line to allow doors to remain locked, whether from the inside or outside. Our handles are designed to fit the majority of standard cylinders, however it is a good idea to double-check before purchasing.

If you wish to upgrade to dual spindle levers, you'll need to remove the handles you have already installed and disassemble the lock case. This will require an additional split cylinder inline. These are available separately and we offer a full technical diagram that you can look at in the images for each product.

Once you have removed the screws that are holding your existing door handle it is a good idea to loosen them and inspect the mechanism to determine what condition it is in. You may need to loosen the screws further if they are not tight, and then you can take off the old spindle and handle and install your new upvc door handle. Before putting the handle in the frame, it is a good idea to make sure it is in the proper position. You can do this by inserting your finger into the gap between the patio door handle frame and the handle to make sure it is in a level position.

Lever/Lever

The lever handles for doors are used to operate a multi-point lock that uses a Euro cylinder. They can be found on a variety of double upvc doors as well as aluminium and wooden doors. They come in two types, with the lever inside and a paddle on the outside. Sprung - they have a spring cassette fitted inside the backplate to bring the handle lever to the horizontal position. Non-sprung - they do not include a spring mechanism and will need to be manually pulled to bring the handle lever back to its horizontal position.

To fix the door handle of a lever that is sagging you must find the hole for access to the detent or pin, which is typically an elongated or rectangular shaped hole or protruding pin situated on one side of the handle base plate. Once you have located the detent access hole or pin, you are able to take it out using the help of a screwdriver.

Once the handle has been set horizontally, it is possible to put back the screws. Tighten them to ensure that the handle is securely connected to the base plate. Consider applying a threadlocking solution to the threads of screws to increase grip and prevent them from loosening over time.

Drooping lever door handles for double glazed doors can be caused by various causes. The most common reason is that the fixings are over tightened, and are putting pressure on the bearings that are causing it to bind against the door face. It could also be that the levers have not been operated at the correct angle, which causes compression of the latch mechanism, preventing it from fully springing into operation.

The most common reason for spring levers that are not functioning correctly is the spring not being in the correct position on the backplate. The simplest way to check this is to turn the handle and see whether it changes to its horizontal position.

If your door handles are loose, it is crucial to find the issue quickly, since this can lead to excessive wear on the screws, and even to the handle falling off the base plate. It is also a good idea to tighten all loose screws regularly to help to prevent them from loosening.

Lever/Snib

The handles for doors made of upvc are also referred to as handle sets with a 'Snib' and have a snib button at the top of the lever that you can press down to lock your door if you don't use a Dummy lock. These door handles are fitted with the Fullex lock 68PZ. (68mm between spindle and lock centre). We also have a selection of 68PZ door handle from manufacturers such as Ferco and Fab & Fix.

Change your door handle is an inexpensive method to upgrade your home, regardless of whether you're replacing a window handle existing handles or fitting new ones to doors you've built in your house. There are a variety of door handles made of upvc with traditional levers on backplate, straight or curving short latches and knob handles with dummy handles for multi point locks which are ideal for French doors.

Lever on backplate handles are typically rectangular in shape, however there are also oval or circular versions, which are known as rose door handles. These handles for doors are identified by a lever or a knob that is mounted on the backplate. The backplate can be removed to allow for concealed fixing.

There are a wide range of chrome and colored finishes available for these handles to match your door and other hardware, like hinges, knobs, bolts and so on. Some handles come with grub screws that aid in the secure attachment of the lever or knob to the spindle. Other handles are supplied with bathroom spindles that can be used to control bathroom locks and feature a thumbturn turn as well as a release mechanism, perfect to use on doors for bathrooms.

Mortise

The tubular latch is the most likely to be the cause if your uPVC door handle is slammed shut. There are a few reasons for this, the most common being the simple lack of lubrication on the latch plate. This can be corrected easily by simply opening the door and spraying lubricant over the lock and handle. It could also be that the latch has slipped away from the backplate. This could be more complicated and will require a specialist to repair.

A multipoint handle is the best solution for stuck door handles. These handles mount through the door's faceplate and are operated with the thumb turn knob or key that activates an electronic cam that locks the deadbolt. The handles are available in various sizes to fit various kinds of uPVC doors and are available in various attractive finishes that are compatible with the hardware that is currently in use. The handles are available via the internet or at the local locksmith. They are easy to install and come with clear instructions.

To choose a replacement handle set, you will need to be aware of the PZ size of your cylinder. This is the distance from the edge of the door frame to the centre edge of the hole in the handle in millimetres. You will also need the type of lock that is installed on your door, whether it's a mortise or hook lock. Once you have these measurements, the easiest method to locate the correct handles is to filter by brand option on the website. This will help narrow down your options and then you can select the right size.

A typical set of handles includes a handle unit comprising two screws of different lengths, drill guides, and installation instructions. Smarter versions, such as the Igloohome Smart Mortise 2+ include a mortice lock with keypad. These are more sophisticated models and are ideal for professionals who install them or skilled DIYers. Some handle sets include an array of additional accessories, such as weather strips, that can be used to enhance the appearance of the door.