Peugeot 208 Key Replacement

Peugeot 208 key replacement is best left to professional auto locksmiths who have the right equipment and know-how to get a new peugeot car key. They can create and program new keys much faster than a dealership would and at a lower cost.

A dead coin battery is the most likely cause when your key fob stops locking or unlocking the doors. But, there are other reasons why the key might be malfunctioning.

Dead Coin Battery

A dead coin battery will stop your Peugeot 208 from locking and unlocking, as well as making it impossible to start the engine. In this scenario you'll need to make use of the alternative method for starting that is described in the owner's manual.

The spark plugs can also be worn out. The spark plugs are responsible to ignite the fuel that ignites the engine. They are only able to last for a short time. If they're not used enough and they fail, they'll eventually die.

Luckily, there's an easy solution to this problem. Check the voltage of the battery using a multimeter. If the voltage is lower than 11,5 volts, it's time to replace it. If the battery is damaged it is necessary to clean its contacts. This can be done by lifting the rubber covers that protect the two terminals on the battery and using a wire brush to remove any corroded parts of the battery. Then, reconnect the positive pole cables to the negative.

Water Damage

If your 208 doesn't start and the battery hasn't gone flat, you should examine the spark plugs. It is possible that they're overly filthy, making them unable to spark. This can be fixed easily by cleaning the spark plugs in the workshop.

Peugeot cars are equipped with a key with a transponder that is compatible with the immobiliser. This ensures that only a valid key can turn the engine. If the chip inside the Peugeot key is damaged then it will not transmit the correct signal to the vehicle.

This is a frequent issue that can occur due to water damage. This is a frequent issue in more cold climates where the car is exposed to snow or rain. In this case, you need to contact an experienced locksmith who will have the tools and equipment needed to modify the key. They will also have all the latest technology and equipment required to make a Peugeot smart key. The process shouldn't take longer than 15 minutes.

Contacts to the battery are not working properly.

Peugeot replaced the old transponder chips using a new key for peugeot 207 type that uses electronic components that are mounted on a circuitboard. The new system is great when it's new, but the circuit boards degrade over time and stop working properly.

This can stop the immobiliser from triggering so that your vehicle won't start. Contact an Peugeot specialist or a locksmith if this is the situation.

A common issue occurs when the battery inside the key fob begins to fail. This causes the blade of the key to stop feeding into your lock. A car locksmith will replace the battery, and cut a new blade for you. This is a simple fix.

Faulty Receiver Module

It could be that the receiver module has a problem when your Peugeot key fob isn't working after being dropped on the floor, exposed to a sudden storm or accidentally washed. The receiver module is responsible for transmitting radio frequency to the onboard computer which controls the central locking system of your Peugeot vehicle.

The rubber seals on the key fob prevent water from reaching the electronic chip. However, prolonged exposure to water may break through these seals, causing damage to the chip. Submerging the key fob into the ocean at the beach or throwing it into the pool can be especially damaging because of the high salt content.

The module will have to be replaced if your Peugeot spare key isn't working anymore. This can only by done by a Peugeot specialist or a professional auto locksmith. Unlike other cars, Peugeot keys are protected by an immobilizer that is unique and requires the correct code to start the engine. This is why you must choose a reputable Peugeot locksmith to take on the job of programming and creating an alternative.

Computers with faulty on-board computers

The computer on the board of your peugeot 107 key fob not working is responsible for a number of the systems inside your vehicle, from airbags to power windows. The on-board computer will display a code if something goes wrong. This code is stored in the system and remains there until the problem is resolved. In most cases, this will require replacing the computer on board.

The most frequent cause for the airbag warning light to flash is corrosion or loose connections within the sensor. This can be caused by wear and tear, age or exposure to salt and moisture. It is important to have this issue resolved as soon as you can, since an airbag that is malfunctioning can be dangerous in the event of an accident.

If your Peugeot is showing a card detected as not present error, the battery inside the key fob may be weak or dead. This will stop the key fob sending a signal to disable the vehicle's immobilizer. Try this by pressing the unlock button on the fob's key, then trying to start your vehicle. If this does not work it is likely that the battery is in need of replacement.