Peugeot 3008 Key Fob Problems

Peugeot's mid-sized 3008 SUV has lot to offer. It's smooth to drive, looks good and has a surprising large boot. But is it able to beat off strong competition in the most crowded area of the market?

If your Peugeot key fob isn't functioning, it may have been exposed to clean tap water or soapy water. You may need to take off the battery, clean it with isopropyl ethanol or an electronic cleaner.

Dead coin battery

Peugeot key fobs are powered by the size of a coin. The power used to control the remote locking system, as well as other features. This battery has a finite life span and may wear out over the course of years of usage. A simple method to determine whether the battery is faulty is to run an electrical test. Multimeters are used to measure the voltage between the plus and minus poles of the battery. The results of this test will show whether the battery is dead or not.

If you've been using your Peugeot 3008 for a while and the key fobs have stopped working, there may be an issue with the receiver module. The receiver module is responsible for receiving radio frequency signals from key fobs, and then sending them to the vehicle's systems. If the receiver module is defective and not functioning properly, it won't be able send commands to other modules within the vehicle.

Another common cause of a key fob that is not working is moisture or sweat in the circuit board. This can result in short circuits, which could draw the battery out and also disable the feature that locks the fob's remote. If this is the case you must take your key fob in to a technician that specializes in chip level repairs.

Water damage

If you dropped your key fob into the pool, tossed it in the washing machine or even put it in the rain for too long, water damage could be a major issue. Water makes for a good conductor, and it can also short out parts of the circuit board. It can also cause corrosion to metal connections on the key fob and other components. A circuit board that is wet can also cause the battery dump its charge.

If you have a spare key fob, use it to lock or unlock your Peugeot 3008 to eliminate the possibility that a dead battery is the cause of the issue. Another issue that can stop your key fob from working correctly is interference signals that interfere with the signal transmitted to the receiver module. These interference signals are triggered by a variety of sources, including radio transmitters within the close vicinity.

If you hear sloshing noises coming from your Peugeot 3008 when driving, this is likely due to a blocked condensate drain for the evaporator. You can test this by blowing compressed air into the drain holes underneath your door. You can also use a flexible wire to wiggle the drain holes and dislodge any dirt that may have built up there. The sloshing sounds can also indicate that there are air pockets in the coolant system.

A malfunctioning receiver module

The receiver module in a Peugeot 3008 is responsible for transmitting a remote keyless message from the keyfob to a receiver inside the car. The receiver module could be damaged, preventing the car from accepting your key fob. This issue can also be caused by the battery being dead or water damage. Or, interference from electronic devices operating at the same frequency. In these instances the car could display a message saying "card not detected" on the display.

Luckily, there are a number of ways to troubleshoot this issue. Try replacing the battery or reprogram the key fob. You can also start the vehicle with a spare key. If the key fob still doesn't work after following all these steps, it could be a problem with the chip.

The best way to know if the key fob has a faulty chip is to take it off and clean it with paper towel and rub alcohol. If the chip has gone bad you need to buy an entirely new key for peugeot 207 one. FB Series enclosures are designed for a key fob and come with a coin battery holder that can fit the most common types of key fob batteries. These enclosures are customizable by using digital printing or CNC-machined cutouts. If your key fob was exposed to salted or dirty tap water, it's possible that the chip has been infected.

Faulty keyless entry system

If you receive the message "card not detected" It signifies that your car can't receive the signal from your key fob. This can be due to many reasons including an insufficient or dead battery. The issue is usually resolved by pressing the start button on the key fob. In certain instances however, you might require taking the key fob to a Peugeot dealer for further repairs.

The first step to troubleshooting the issue with a Peugeot 3008 key fob that's not able to unlock or lock the doors is to check its battery. Batteries are often the main cause of a malfunctioning fob however, there are other causes that can contribute to this issue as well. They include worn buttons, damage to the receiver module, water issues and signal interference.

If you've recently been exposed to water and have your Peugeot key fob exposed to pure tap water it's best to remove the battery and dry the electronic components using paper towel. You can also use isopropyl Alcohol or a cleaner for this purpose. It is best to change the fob if it's been exposed salt water or soapy water.

If your key fob still doesn't work, you can reset it by taking out the battery of 12 volts for 15 minutes. Connect the negative cable, then the positive cable.