How to Replace a Kia Sportage Replacement Key

For many kia rio key replacement (Suggested Reading) models, the key contains an integrated keyless entry system. The key functions like remote controls and is exchangeable by a Kia dealer.

Key fobs can stop working due to a variety of reasons, including the battery of the coin is dead, worn buttons, signal interference, water damage and a malfunctioning receiver module. Here are some guidelines on how to get your Kia Sportage replacement key back to working.

How do you replace a remote key or smartkey

The battery in your kia keyless entry's intelligent key will eventually need to be replaced, regardless of whether it is a remote key or a push-to-start one, or a regular metal key that does not contain an electronic transponder. This is especially in the event that your car displays a message that the remote or smart key is not powered by the battery.

Fortunately, it's quite simple to do. In order to replace the battery of the key fob take out the mechanical key from the slit at the back of the key fob. Then break the cover. Inside the key fob, there will be the small screw that holds the battery in its place. By using a small screwdriver unscrew the screw and pull out the battery that was in place. Insert the new battery and close the slit on the key fob.

When the key fob is equipped with an updated battery check it by pressing the locks and unlock buttons. You're good to go If the doors lock and unlock as you expect. You can now use the hands-free feature to lock and unlock your Kia whenever your fingers start to get cold or when you need to do some errands in Brandon.

Note: Some keys may require to be programmed (transponder chips or smart keys). This requires a programming machine, which is only available to the locksmith who works for the automotive dealer. Other keys (non-transponder metal keys) do not require programming. If your key needs to be reprogrammed, you will need to be aware of the number stamped on the key code tag and record it in a safe place.

How to replace a battery

If your Kia key fob is not responding when you press the lock or unlock button on the fob, this is a clear indication that the battery needs to be replaced. A weak battery could cause other issues, like the check engine light turning on or the engine not cranking properly. Fortunately, replacing the battery on the key fob is a relatively simple DIY project that requires just a few tools.

Be sure to turn off your vehicle and shut all doors prior to beginning. Find the small, metal or plastic piece that is on the bottom of your key fob and jiggle it until a metal key slips out. This key can be placed inside the driver door handle to unlock your car.

To replace the key fob battery, remove the cover from the back and use a plastic pry bar tool to remove the latch holding the black negative battery cable. Remove the old battery and orient the new battery so that the "+" positive side is facing you, while the "-" negative side is facing the fob's electronic contacts. Avoid using excessive force when pushing the new CR2032 into place to avoid damaging or bending the metal contacts.

Once the new battery has been installed then turn the key fob off and then on in the ignition for a few times until the door locks cycle. You can then test your Kia's key fob once more to ensure it's working as intended.

How to replace the smart key?

Depending on the model of your Kia Sportage, you may have an ordinary key fob or a smart key. The smart key comes with an embedded mechanical key blade, while the standard key fob does not. Both types of key fobs have batteries inside which eventually needs to be replaced. Luckily, this is an easy task that takes only two minutes.

Before you begin before you begin, ensure that you're on a flat surface with enough lighting and that your kia picanto replacement key cost is turned off. Also, keep in mind that there are tiny pieces inside the fob which could fall out if not vigilant.

The first step is to find the small release button that is located on the back of the lower part of the fob. It could be a circular button or rectangular slot. After pressing this button the mechanical key blade will come out and you will be able to open the key fob.

After the key fob has been open, remove the battery. The new battery should be a CR-2032, and can be purchased online or at a local auto parts store. After you're done, your key fob should permit you to lock or unlock and start your vehicle, even if it isn't running.

How do I replace a mechanical key

The Kia keyfob can be a fantastic convenience which allows us to lock or unlock our car with just pressing one button. But, as with all devices it will encounter issues from time to time. Luckily, there are ways to resolve these issues and ensure that our key fobs are in good working condition in the long run.

A dead or low-quality battery is among the most common problems. This could cause the fob to stop working entirely or to work intermittently. If this is the issue you should replace the battery a new one.

If this doesn't solve the issue, try using a standard flathead screwdriver to push the plastic casing of the fob open. Be careful not to damage any internal components or scratch the plastic. Once the battery is opened, carefully remove the battery you have been using and replace kia key it with a new one.

Close and open the door using the mechanical key. (Every Kia fob comes with a spare mechanical key which will fit into the slot). Test the key fob and check that it's functioning correctly. If the device isn't functioning, contact an authorized locksmith or dealer to resolve the problem. To avoid locking outs in the future, ensure you have an emergency key that can be able to work with all trunk and door cylinders.