Double Glazing Door Lock Repairs

Has your uPVC window or door mechanism started to fail? Perhaps the handles on your upvc repair windows and doors are not aligned properly or are difficult to use.

You will lose energy if your double-glazed doors don't perform as they should. This also increases the risk of burglary. Owen the Locksmith can repair your door lock for a reasonable price.

Snapped Key

It can be quite frustrating when a key snaps inside a lock. This can also be a security risk, as it may leave you vulnerable to burglars if your door does not lock. There are a couple of quick fixes you can try to fix the problem and get your door working again.

First, remember to stay calm. If you get scared and start poking around wildly you may end up pushing the broken piece of the key further into the lock, making the situation even more difficult.

Then, spray WD-40 or another penetrating oil into the lock to aid in making the broken piece slip out more easily. You can also use the screwdriver to break any pieces stuck. If you have a chunk of the key still sticking out, grab it with a paperclip or another thin metal object and pull it. Both of these methods work well, but be careful not to push the damaged piece of the key deeper into the keyway.

Some paperclips have grooved edges that can serve to extract hooks and jigsaw blades are also suitable for this purpose. If you don't have any of these available, you can use needle-nose pliers to bend them and create a hook. Additionally, you can use a pair of tweezers grab and remove the last piece of broken keys.

If you cannot remove the broken piece of key then you can use a lock deicer. It is available in most hardware stores and works by freezing any moisture that may be present inside the lock.

If none of these solutions seem to work, it might be time to call a locksmith. Fitlocks experts can fix issues such as broken handles or snapped keys with upvc repair locks and door mechanisms. They can also alter your double glazing door mechanisms to make them more user-friendly. Request a repair for your double glazing through us online or give us a phone call to discuss your requirements.

Broken Cylinder

A damaged cylinder can pose an immediate security risk. It's fortunately a simple repair for an expert locksmith to complete. To repair the cylinder, locksmiths will need to tap it. This can be accomplished with a hammer or other tool. The best method is to use a wire or a long match. The match or wire end near the keyway. The locksmith will then strike the lock in order to break it. This is superior to using the hammer, which could damage the lock.

The most frequent cause for cracks in the cylinder head is overheating. This can happen when the block and cylinder head are made from different metals such as cast-iron and aluminium. When various metals heat up and cool down at different rates, it can create hotspots in the local area that expand faster than the rest of the cylinder head, thus leading to cracks.

Another possible cause for cylinder cracks is corrosion. If the head and block of a cylinder are not maintained properly they could be corroded or rust, which can cause them to expand faster than they would normally. This can cause cracks in the future.

If your uPVC window or door lock is stiff or requires an enormous amount of pressure to turn, this could be due to a number of things. A defective locking mechanism, misalignment, or the wear of the handle are typical causes of this issue.

This is a straightforward and inexpensive fix that most double glazing owners can do. A professional locksmith can usually solve the issue within one hour of arriving at the property. Depending on the needs of your home, they can replace the locking mechanism, replace the window handles, and also change the gearboxes. A professional locksmith will always be able to advise you on the most cost-effective options for your home. They can also suggest upgrades to 3 Star security TS007 euro cylinders that will give you an additional layer of protection against burglars. It's a small amount to enjoy the peace of mind that comes from knowing your uPVC door is secure.

Broken Handle

It's not a surprise that window handle locks may break. They have intricate mechanisms that wear out over time. If yours breaks, it can be difficult to pinpoint the cause of the problem and make sure you fix it properly.

Repairing your damaged handle, whether it's an internal locking mechanism or latch will increase the security of your uPVC door and prevent draughts. Incorrectly repairing or replacing the handle could be costly and may harm the door's frame as well as lock It is therefore worth taking the time to do it correctly.

With the Window Doctor near me in the open position, loosen the screw that holds the handle with the screwdriver. The screw should be located on the inside of the backplate, which is usually concealed by a screw cap to enhance the appearance. Be sure to not lose any of the internal components within the handle, like the levers or plates on either side of the spindle. Keep them in the same order to make it easier to replace them if needed.

Then, turn the handle until it's 90 degrees to the window frame and loosen the screw at the back of the handle that fixes it to the internal spindle by using a second screwdriver. Once the screw is free, you can remove the handle and remove the broken spindle. Replace it with a brand new spindle, ensuring that it's the same length (you can buy them on the internet or in hardware stores). Screw it into the frame. Do not overtighten the screw as this could damage the handle and the window frame.

Ensure the new handle is fitted, then close and test the handle. Hopefully, it will work smoothly and you'll be able to unlock your window.

Don't forget to double-check that your uPVC window is closing properly while you're working with the handle. If they don't, you could experience draughts and damp in your home, as well as compromising the efficiency of your home's energy usage. A local window company, such as Core Sash Windows, will be in a position to adjust the hinges on your window frames so they can shut properly.

Broken Spindle

It is more likely for the spindle to break than the handle. This is most common in uPVC tilt and turn windows. These windows require a handle which is a lock mechanism that is located in the frame of the window. The handle is attached to a central rod that triggers the cams with a mushroom shape that secure the window frame keep. If the dead latch mechanism is not able to open when the handle is turned, it is likely that the spindle is broken and this could be a very frustrating issue.

Luckily, there are steps that can be taken to fix this problem. A skilled locksmith can quickly and efficiently solve the issue. They will be able to disassemble the window handle by using a tool that removes the wheel portion of the mechanism, where the spindle is. This is done without damage to the handle or the window frame.

Once the wheel has been removed the technician can then inspect the spindle and determine what caused it to break. This involves breaking down the spindle into its component parts and meticulously noting their general condition as in addition to any specific areas of wear or damage. This procedure is usually carried out in a clean, well-lit room by highly skilled technicians.

The next step is to clean the damaged spindle. This will remove any dirt or debris that might be obstructing its normal function. The spindle may then be repaired or replaced. If the technician is replacing the spindle it is possible to use a dowel that is the same size to the original. The technician will then drill holes that are identical to both pieces. This ensures that the new spindle is a precise fit with the handle.

If the damaged spindle can't be repaired, it might require replacement completely. Home centres sell generic replacements. However, if the style of your window is unusual then you will need to speak with a woodworker or cabinet maker who can replicate the exact component for you. Once the new spindle is installed, it can be positioned to the handle by lining up the screw holes on the handle with the frame's existing screws. Once the handle is firmly in place, you can use your uPVC windows.