Repairs to uPVC Windows

uPVC windows are an excellent choice for modern homes. They are durable, long-lasting and easy to maintain. They are not susceptible to rot or rust like timber and aluminum.

Regularly cleaning and lubricating UPVC windows and doors is crucial. This will reduce repair costs and increase energy efficiency.

1. Broken Glass

The broken glass in your windows could cause significant damage to your home and may even be fatal. You should take the time to ensure that your windows are in good condition.

Single-pane windows are relatively easy to replace and typically fit into frames of the past easily. If you have double-paned windows that are joined by internal beading, it is more difficult to remove and replace the old panes. In this situation it is essential to purchase plastic spacers in order to help the new pane fit into the window frame.

If you're planning attempt to remove the window panes yourself it is important to wear the proper safety gear such as gloves that are thick and eye protection. It is also recommended to lay down a drop cloth before you begin working on the glass so that any shards fall onto the cloth instead of onto the floor where they can be trodden under and cause further damage.

It's a good idea to cover the gap with tape after the glass is removed. This will stop drafts and water from getting into your home until a professional arrives to repair the window. It also acts as a barrier that will prevent any intruders from gaining entry to your home. If the distance between the door and the window is significant, you may need to consider an alarm system that has an opening. This will provide the best of both.

2. Sagging

uPVC is durable and energy efficient alternative to timber sash windows. However, over time, they can suffer from a variety of problems including sagging. A window that isn't properly aligned can cause problems with light, draughts, and even security. It's crucial to act immediately if you discover that your uPVC windows are sliding.

To fix a sagging window you can try to reposition the hinges. First, you'll need to unblock the windows to access the frame. After that, using the screwdriver, you'll be able to unscrew the hinges at the top and bottom and adjust them by turning them clockwise or anti-clockwise. Close your window to test the fit after you have relocated your hinges. If you're satisfied with the fit, you can tighten the screws to ensure they remain in place.

If you can't reposition the hinges, you might need to replace the seal. Rubber seals can dry out and lose their elasticity over time, causing them to lose their tightness. It is essential to replace your seal as quickly as you can to keep your uPVC window watertight and draughtproof.

uPVC handles can also loosen up. Often this is due to screws that have come loose over time. However, it could be due to the fact that the handle mechanism has worn out. It's fairly simple to fix a loose uPVC handle. First, you'll need to shut the window and perform an experiment fitting. The joints at the corners of the sash should align with the joint on the casing. If it isn't, you can use a screwdriver to loosen the handle and then reverse the mechanism back into the position it was in.

3. Water Leaks

If you're waking up to wet floors and damp walls each time it rains it's important to take action. The leaks of water from windows do not only lead to the destruction of your home's structure but also undermine your efforts to control the temperature within your home. Most of the time, uPVC window leaks are caused by a damaged or missing sealant.

This is a relatively easy fix that can be done by any skilled DIYer. Depending on how severe the issue is, old caulking may have to be removed. It is essential to keep in mind that when it comes to uPVC window repairs you should not be tempted to apply too much caulk and then make the area more difficult to clean and can reduce your energy efficiency.

Verify that the drainage holes are free of debris inside them and that the sill pan has been angled correctly to drain away from the window. In more severe instances, you may need to replace the window.

Mold spots and rotten sills are also signs of water leakage. The fungus thrives in damp conditions and can quickly spread across the home.

If the leakage is occurring between the double-glazed glass, it is more likely the problem is related to the seal, not the frame. This can be easily fixed by a uPVC window expert who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or loose and open in a breeze It could be hinges that are at fault. They can be easily repaired by any DIYer who is skilled and can be completed in a matter of minutes.

Nearly every home in the UK will have either top hung or side hung upvc window repairs windows that use hinges and like any mechanical part they are susceptible to wear and tear over time. The process of replacing a hinge on a window is an easy procedure, but it is simpler with someone else to assist in holding the frame up.

Make sure that the uPVC hinges open and close in the proper direction. Look for the arrows on each hinge to determine which way the window should be opened.

Window hinges that aren't working properly could be caused by improperly opening the window in a particular way or by poor installation at the factory. This issue can be fixed by sending us a photo via our website and we will be happy to give you suggestions.

It is also essential to grease the hinges on a regular basis. Applying an engineering lubricant that is light to the hinges is a great method to accomplish this. We recommend using an oil that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regularly lubrication will help the window operate and close more easily. It can also lower the chance of windows sticking and help prevent corrosion. Ideally, you should do this once a year. WD40 or other solvent-based oils should not be used since they could damage your uPVC windows.

5. Draughts

Draughts can be caused by a variety of different things. The hinges can also become unbalanced due to wear, which can cause gaps where the sash and frame meet. If they are damaged beyond repair, it could be necessary to have them realigned. Secondly the interlock, this is located on the hinge side of the window, can also be misaligned, and again it is possible to give them a thorough clean, however in some instances it could be necessary to get them replaced.

The second most frequent reason for draughts are the window seals. They can become worn down or damaged over time, and will allow air to escape through these gaps. This can be avoided by replacing them with high-quality weatherstripping. Replace the upvc windows with low-emissivity lenses. This will help regulate indoor temperatures and lessen the possibility of draughts.

One of the most effective ways to cut down on drafts is to use an draught excluder. These are typically made of fabric which are filled with a kind of filler. They can be placed on the top of your windowsill. They can help keep cold air out and keep your home warm and cozy!

With a bit of regular maintenance and repair, your upvc windows will provide a great level of security and insulation for your home. It is crucial to recognize that all windows have a lifespan and they may reach a point where it is more efficient to replace them than repair them. So, if you are experiencing issues with your Upvc windows, it's best to seek professional assistance immediately.