Repairs to uPVC Windows

uPVC is an excellent choice for modern homes. They are easy to maintain, durable and long-lasting. They don't rot or rust like timber and aluminum.

It is essential to clean and oil UPVC windows and doors regularly. This will help avoid unnecessary repair costs as well as improve the efficiency of energy.

1. Broken Glass

If the glass in your window is broken it can cause a huge deal of damage to your home, making it extremely dangerous and possibly fatal. It is important to ensure that your windows are in good condition.

For single pane windows, it can be relatively simple to replace them, and the replacement is usually able to fit into the frame that was previously installed easily. However, if you have double glazing-pane windows that are held in place by internal beading it will be more difficult to take out the existing panes and install new ones. In this instance, you will need to source some plastic spacers to help the new pane to fit properly into the frame of the window.

Wearing eye protection and thick gloves is essential when you are planning to remove the glass by yourself. You should also lay down a dropcloth prior to you begin working on the window panes, so that any shards fall onto the fabric and not on the floor, where they could be trampled.

Once the glass has been removed and the glass is removed, it's a good idea to seal the gap with some clear packaging tape or duct tape to block water and drafts from getting into the home until a professional comes out and repair the window. It also acts as a barrier, preventing any intruders from getting access to your home. If the gap is large, you might be interested in a security door that has an integrated window as it offers the best of both worlds.

2. Sagging

uPVC is a durable and energy efficient alternative to timber sash windows. As time passes, they may develop a variety of issues, including sagging. A window that is sagging can cause problems with light, draughts or even security. If you find that your uPVC window is beginning to lose its shape, it's crucial to act fast to prevent the problem from getting worse.

To repair a window that is sagging, you can try repositioning the hinges. To do this, you'll have to open the window to access the frame. Then, remove both the hinges at the top and bottom using a screwdriver, and then adjust the hinges clockwise or counter-clockwise. After you've repositioned the hinges, shut your window and check for fit. If you're satisfied with the size of the window, tighten the screws to keep them in place.

If you cannot reposition the hinges, you might have to replace the seal. Over time, rubber seals lose their elasticity and become dry and cause them to lose tightness. It is essential to replace your seal as soon as you can to keep your upvc repair window watertight and draughtproof.

uPVC handles may also loosen. This is typically caused by screws that have been removed over time, but it could be due to the handle mechanism wearing out. It's a good thing that it's simple to fix the handle of a window that is loose yourself. First, you'll need to close the window and do an experiment fitting. The joint at the corners of the sash must align with the joint on the casing. If it doesn't then you can use the screwdriver to loosen up the handle. Then, turn the mechanism back into place.

3. Water Leaks

If you awake to wet floors and damp walls each time it rains, it's important to take action. Water leaks through windows can cause structural damage to your home and also impact your ability to regulate the temperature of your home. The most frequent reason for leaking uPVC windows is that the sealant around the frame is damaged or not present.

This is an easy fix that can be accomplished by any DIYer who is competent. Depending on the severity of the issue is, the old caulking may need to be removed. It is essential to keep in mind that when it is about upvc repairs near me (Article) window repairs, you should not be tempted to 'over-caulk' as this will only make the area more difficult to clean and could reduce the efficiency of your energy.

Make sure that the drainage holes do not have debris in them, and also that the sill pan is angled correctly to drain away from the window. In more serious situations, you might need to consider replacing the window.

Other indicators of long-term water leakage are rotted sills and the appearance of black spots of mold on the walls near the window. The is a fungus that thrives in damp conditions and can quickly spread across the house.

It is also important to note that if the leakage is coming from between the glass of your double glazed windows, it's more likely to be an issue with the glass seal, rather than the frame or sagging. This can be easily fixed by a uPVC window expert who can replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or loose and blow open with ease it could be hinges at the fault. Any competent DIYer can replace the hinges in a matter of minutes.

Like any mechanical component, hinges can be damaged over time. It is essentially a simple procedure, but it is easier to do with someone else to assist in holding the frame up.

Check that the uPVC hinges are closed and open in the correct direction. Check for the arrows on each hinge to determine which way the window should be opened.

Faulty window hinges could be the result of incorrectly opening the window in a particular way or due to improper installation in the factory. Sending us a photo through our website can often solve the issue. We are happy to give advice.

It is also essential to lubricate the hinges on a regular basis. Applying an engineering lubricant that is light to the hinges is an ideal way to do this. We recommend using an oil that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regularly lubrication will help the window to operate and close more smoothly. It can also reduce the risk of a window sticking and prevent corrosion. This is recommended to be done at least every year. WD40 and other solvent-based lubricants should not be used since they can cause damage to your uPVC windows.

5. Draughts

Draughts in windows made of upvc can be caused by a few different things. The hinges can also be misaligned due to wear, which can cause an opening where the sash and frame meet. These can be easily fixed by giving them a good cleaning, but in the event that they are beyond repair it might be necessary to get them realigned or replaced. The second is the interlock, which is on the hinge side of the window and can be misaligned. Again, it's feasible to give them a good clean, but in certain cases, it may be necessary to get them replaced.

The seals may wear out or be damaged over time, allowing air to escape. Replacing these with high-quality weatherstripping will help to stop draughts. Replace the windows made of Upvc with low-emissivity lenses. This will help control indoor temperatures and lessen the risk of draughts.

Lastly, one of the most effective methods to reduce the draughts in your home is to use a draught excluder. These are typically fabric tubes filled with some type of filler. They can be positioned on the top of your windowsill. These will keep your home warm by blocking out cold air.

With a little regular maintenance and repairs, your upvc windows will continue to provide excellent security and insulation for your home. It is crucial to keep in mind that all windows eventually become worn out, and it may be more cost-effective to simply replace them than to repair them. So, if you're having issues with your upvc windows, it is always recommended to seek help from a professional as soon as you can.