Repairs to uPVC Windows

uPVC windows are a fantastic option for modern homes. They are easy to maintain, durable and long-lasting. They are not susceptible to rot or rust like aluminum and timber.

Regularly cleaning and lubricating UPVC windows and doors is vital. This will help prevent unnecessary repair costs and also improve the efficiency of energy.

1. Broken Glass

The broken glass in your windows can cause significant damage to your home, and could even be fatal. It is essential to take the time to make sure that you are doing everything you can to ensure that your windows are in good repair.

For single pane windows it is relatively easy to replace them, and the new window will generally fit within the frame of the previous one easily. However If you have double-pane windows that are secured by internal beading, it'll be more difficult to remove the existing panes and install new ones. In this case you'll need locate some plastic spacers to assist the new pane to fit perfectly into the window frame.

Wearing eye protection and thick gloves is a must when you are planning to remove the glass by yourself. It is also recommended to lay down a drop cloth before you begin working on the window panes so that any shards fall on the fabric and not onto the floor which could cause them to be trampled.

Once the glass is removed and the glass is removed, it's a good idea to seal the gap with clear packaging tape or duct tape to prevent water and drafts from getting into the home until a professional can come out and fix the window. This will also act as a barrier, preventing any intruders from gaining entry to your home. If the gap between the door and the window is large, you might need to consider security screens that has an opening. This will provide the best of both.

2. Sagging

Upvc windows and doors are a low-cost energy-efficient, durable and long-lasting alternative to timber windows made of sash. As time passes, they may develop a number of problems, including sliding. A window that isn't properly aligned can cause problems with light, draughts or even security. It's important to take action immediately if you realize that your uPVC windows are sliding.

Repositioning the hinges could aid in fixing a window that is sagging. To do this, you'll need open the window so that you can access the frame. Then, you can remove the top and bottom hinges with a screwdriver and adjust the hinges clockwise or counter-clockwise. Close your window to test the fit after you've relocated your hinges. If you're satisfied with the fit, tighten the screws to ensure they stay in place.

If you are unable to reposition the hinges, you might need to replace the seal. Over time rubber seals can lose their elasticity and dry out and cause them to loosen. If this happens, it's essential to replace the seal as fast as possible to ensure your uPVC windows are waterproof and secure from draughts.

uPVC handles may also become loose. Most often, this is caused by screws that have become loose over time. However, it can occur because the handle mechanism has been worn out. It's a good thing that it's simple to repair a loose uPVC window handle yourself. First, you'll need to close the window and then perform a test fitting. The joints at the corners of the sash should be aligned with the joint on the casing. If it isn't, you can use a screwdriver to loosen the handle, and then return the mechanism to its original the position it was in.

3. Water Leaks

If you're waking up to wet floors and damp walls every time it rains it's crucial to take action. The leaks of water through windows could cause structural damage to your home, and affect your ability to regulate the temperature inside your home. Most often, uPVC window leaks are caused by a lack or damage to the sealant.

This is a simple fix that can be done by anyone who is a DIYer with the skills. Depending on the severity of the issue the caulking that was used up might need to be removed before a fresh layer can be applied. When it is time to uPVC repair, it is important to avoid over-caulking. This will make your window more difficult to clean and decrease its energy efficiency.

Check that any drainage holes are free of debris in them and ensure that the sill pan has been angled correctly to drain away from the window doctor. In more severe cases, you may need to replace the window.

Mold spots and rotted sills are other signs of water leakage. The fungus thrives in conditions of dampness and can spread quickly throughout the home.

It is also important to keep in mind that if the leak originates from the glass of your double-glazed windows, it is more likely to be an issue with the glass seal, rather than the frame or sliding. It is also possible to be fixed by a uPVC window expert who can replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

Hinges may be to blame for the reason that your uPVC window is difficult to open or it opens in the breeze. Anyone with the skills to fix them can replace the hinges in a matter of minutes.

Like any mechanical component, hinges can be damaged over time. It is very easy to replace a hinge on a window, but it's easier if someone else helps hold the frame.

Make sure that the uPVC hinges are closed and open in the proper direction. Look for the arrows that are on each hinge to determine which way the window should be opened.

The problem with the hinges on windows could be caused by improperly opening the window a certain way or due to inadequate installation at the factory. Sending us photos via our website is often enough to resolve the problem. We are always happy to offer suggestions.

It is also crucial to grease the hinges regularly. Applying a light engineering lubricant on the hinges is an ideal method to accomplish this. We recommend using a lubricant that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication can help the window to operate and close more easily. It can also prevent corrosion and reduce the risk of sticking. Ideally, you should do this at least once a year. WD40 or other solvent-based lubricants should not be used as they can damage your uPVC windows.

5. Draughts

Draughts can be caused by a variety of different factors. First, the hinges due to wear and tear can become misaligned, this causes a gap to form where the sash joins the frame. If they are beyond repair, it could be necessary to have them realigned. The interlock may be disaligned. This happens on the hinge's side and might require to be cleaned. In certain instances it might be necessary to replace these.

The seals may wear out or become damaged over time, allowing air escape. This can be prevented by replacing them with high-quality weatherstripping. Replace the windows made of Upvc with low-emissivity glasses. This will help control indoor temperatures and decrease the risk of draughts.

Another method of reducing the amount of draughts is to use a Draught-exclusion device. These are usually made of fabric tubes filled with a filler which can be hung over your window sill. They can keep your home warm by blocking out cold air.

With a bit of regular maintenance and repair windows made of upvc will provide an excellent level of security and insulation for your home. It is essential to remember that all windows will eventually become worn out, and it is more cost-effective to replace them rather than repair them. If you encounter any issues with your Upvc window, it's best to consult an expert as soon as possible.