How to Replace a Kia Sportage Replacement Key

For many Kia models, the key contains the keyless entry system that is built into the key. The key is usually akin to an remote control, and can be exchanged with a new one from a Kia dealer or locksmith.

Key fobs can fail to function due to a number of reasons, such as batteries that are dead, worn-out buttons signal interference or water damage. Here are some helpful tips to help you get your Kia sportage replacement key to work for good.

How to replace the remote key or smartkey

The battery inside your kia sportage key fob's smart key will eventually require to be replaced, whether it's a remote as well as a push-to start key or a regular key that doesn't have a transponder. This is especially in the event that your car displays a message telling that the remote or smart key has low battery power.

This is a relatively simple process. To replace the battery on the keyfob, remove your mechanical key from the slit on the back of the fob. Then, pull the cover off. A small screw is located inside the key fob to keep the battery in place. Utilizing a small screwdriver loosen the screw and remove the battery that was in place. Insert the new battery and close the gap on the key fob.

Once the key fob has a fresh battery check it by pressing the locks and unlock buttons. It's good If the doors lock and unlock as you expect. You can now make use of your kia keys replacement's hands-free lock/unlock feature whenever your fingers get chilly or you have to do some errands in Brandon.

Note: Some key fobs (transponder chip or smart keys) might require their programming completed. This requires a specific programming machine that only the dealer or locksmith has access to. Other keys (non-transponder metal keys) don't require programming. If your key needs to be programmed again, you will need to be aware of the key code number printed on the tag that identifies the key and then record it in a safe place.

How to replace a battery

If your Kia key fob is not responding to pressing the lock or unlock button on the fob, this is a signal that the battery should be replaced. A low battery may also cause other issues such as the check engine light coming on or a delay in cranking the engine. Fortunately replacing the key fob battery is a fairly simple DIY task that requires only some basic tools.

Make sure to shut off your vehicle and close the doors before you begin. Find the small metal or a plastic piece near the bottom of the key fob. Press it until the metal key falls out. This key can be placed inside the driver door handle to unlock your car.

To replace the battery on the key fob, take off the cover on the rear. Use a pry tool to open the latch that holds the black negative cable. Remove the old battery and then align the replacement battery so that its "+" side faces you, and the "-" negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position with care to avoid using too much force to avoid bending or damaging the metal contacts.

Once the new battery has been installed and the key fob is turned on, turn it off and on in the ignition repeatedly until the door locks. Then, test your Kia key fob and see if it is working properly again.

How to replace a smart key

Depending on the model of the Kia Sportage, you may have a standard key fob or a smart key. The smart key has an embedded mechanical key blade, unlike the standard key fob, which does not. Both kinds of key fobs come with batteries that eventually will need to be replaced. It is a simple process that takes just two minutes.

Before you begin it is essential to make sure that you are on a flat surface with enough lighting and that your Kia is off. Keep in mind that there are tiny components inside the fob that can be snagged if not careful.

The first step is to find the small release button that is located on the lower backside of the fob. It's either a circular button or a rectangular slot. When you press it button, the mechanical blade will come out and you can then open the key fob.

Once you have the key fob open then you can take out the old battery and replace it. The new battery should be a CR-2032 and can be purchased online or at a local auto parts store. After you're done, your key fob will allow you to lock or unlock and start your vehicle, even if it isn't running.

How do you replace a broken mechanical key

The Kia keyfob is a wonderful convenience which allows us to lock or unlock our car with just pressing the button. However, like all devices, it can have problems from time to time. There are ways to fix these problems and keep your key fobs functioning for a long time.

A dead or low-quality battery is one of the most frequent problems. This can cause your fob to stop working or work intermittently. If this is what you are experiencing, replace the battery with a new one.

If this does not solve the issue, you can use a standard flathead screwdriver to wedge the fob's casing made of plastic open. Be careful not to damage any internal components or scratch the plastic. After the battery has been removed and replaced with a new one.

After the new battery has been put installed, close and unlock the doors with the mechanical key (every Kia Spare Key (Www.Copyoa.Com) fob comes with an emergency mechanical key that will fit in the slot). Test the key fob and check that it's functioning properly. If the fob isn't working, contact an expert locksmith or dealer to help resolve the problem. To avoid a lockout in the future make sure you get an emergency key that will work in all of the trunk and door cylinders.