Reasons Your fiat 500 spare key (Www.kuangjiab.com) 500 Key Fob Won't Work

A Fiat 500 key fob makes it simple to open doors and start your vehicle. There are a myriad of reasons the fob won't work. These include a dead coin battery or water damage, receiver module issues, and interference.

This listing is for an NEW replacement fiat 500 key replacement cost Flip Key Remote - look-alike Ilco brand that needs to be programmed professionally by a local automotive locksmith (click here for Locksmith Search). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is probably the most common reason for your 500 key fob that isn't working. Modern key fobs come with a limited operating range, and should be within only a few feet from the car to operate. If you are not within your car and hit the keyfob, it will not respond, and display the message "Key Fob Not Detected".

If this happens, simply replace the battery on your coin cell (Part number CR2032) with a fresh one from a reliable brand such as Panasonic, Duracell, or Energizer. You can typically find them at your local hardware store or online.

You can test the battery on your coin-cell by pressing the buttons while standing near your Fiat 500. The parking lights should flash and the key fob will operate the lock and unlock switches.

If the fob's key doesn't work after replacing the battery, it could have water damage that stops it from communicating with the receiver module inside your vehicle. Water damage can occur through a variety of methods, including a simple splash or submerging the key fob in saltwater at the beach. If you think your fob was exposed to water, you can place it in a bag of rice to draw out the moisture. If this doesn't work your fob may need to be reset by a professional auto locksmith or dealer.

Water Damage

Water damage can happen if you submerge the fob in the ocean, or wash it in a washing machine. Saltwater is particularly dangerous to the fob's circuit board, causing it to short out and eventually end up dying. In the event that you let your fob get wet, it's not an ideal idea but if you drop it into an empty cup of water, or don't remember to remove it from your pants pocket before running the washer and you don't have a chance, don't give in.

First, remove the battery. Before replacing the battery clean the electronic chip with isopropyl or another similar product. Check the fob again to see if it is functioning. If the key doesn't function then it might need to be reset. This is usually done by an auto locksmith or dealer.

If the key is a newer model and has never been programmed to your car, it will likely need to be replaced completely. A professional locksmith for automotive can do this job. The locksmith will need to cut the key to match the ignition of your vehicle. The locksmith will also need to program your fob into the car's system. It's a simple and affordable process that is usually completed in the same day.

Receiver Module Issues

Your 500 key fob may be inoperable because it's out of range. The remote usually has 30 feet of range or less, and if it's too far away from your car it will not respond to your commands. This can be fixed by moving closer to your vehicle until it starts responding.

If you've replaced the battery in your coin (commonly known as"button" or "button" or "watch") and the fob won't work It could be because of an internal circuit board problem. In most cases, reprogramming the fob will resolve this problem. You can find the procedure for most vehicles on YouTube or in the owner's guide.

It is possible to replace the metal retaining clips that keep the coin battery. If they loose tension, it could prevent your coin battery from being properly seated, causing your remote to malfunction.

In rare instances the fob could be desync'd with your vehicle because of software or hardware issues. This can be a major trouble, but you could usually resolve this issue by visiting an auto locksmith to reprogram your fob. In some instances, they may need to reinstall the program in your body control module, too.

Interference

Interference can also cause the key fob to not be able to receive or transmit an signal. This may happen if the keyfob is located in close proximity to a radio transmitter, like a cellphone or radar detector. The key fob may not function due to a poor connection with the buttons, water damage or damage to the internal chips.

If the key fob stopped working one day in the middle of the night and you've tried everything you can at home to solve it e.g. replacing the battery, reprogramming it and using the spare key fob, it could have a damaged receiver module on your 500. The receiver module is situated under the dash and picks up the radio frequency signals from the key fob. It then converts them into electronic commands that the vehicle interprets.

Fortunately, there's an easy way to reset all on-board systems in your 500 device, including the key fob. Disconnect the battery for 15 minutes by removing first the negative cable and then the positive cable. Reconnect the battery. This will clear out any remaining electricity and then restart the car's computers. This can help get your key fob working again. If the issue persists you should seek out a certified technician. They can identify the exact cause of problems.